SSL-12151M-PC 1-Light Matte Black Outdoor Wall Lantern Sconce Sensor
Product Information
The product is a light fixture that comes with a mounting unit,
screws, wire nuts, and bulbs (not included). The fixture can be
used for outdoor and indoor lighting and comes with a light control
switch that automatically turns on the light at illuminance 10Lux
and turns it off at illuminance 30Lux. The product has a rated
voltage of 120VAC/60Hz and can be used with LED lamps/ballast of up
to 39W or incandescent lamps of up to 100W. The product also has a
photosensor that should be installed in a place with good
photosensitivity and without obstacles affecting its acceptance of
natural light.
Product Usage Instructions
- Before starting the installation, make sure to have a ladder,
safety glasses, electrical Phillips, tape, screwdriver, flat blade
screwdriver, pliers, and wire strippers. - Unscrew the ball nuts from the mounting unit and use the
mounting screws to attach the mounting unit to the junction box
(not included). - Make the electrical connection from the junction box to the
fixture. Connect the ground wire to the mounting unit using the
preinstalled green ground screw. Then, connect the positive,
negative, and ground wires with the supplied wire nuts. Secure with
electrical tape. - Attach the fixture to the mounting unit through screw holes as
shown and secure it with screws. Use caulk in the backplate and
wall mounting surface to prevent water from entering. - Install bulbs (not included).
- To operate the light fixture, turn on the light control switch.
The light will automatically turn on at illuminance 10Lux and turn
off at illuminance 30Lux. - Make sure to install the photosensor in a place with good
photosensitivity and without obstacles affecting its acceptance of
natural light. There should be no swinging objects in front of the
photosensor.
ASSEMBLY INSTRUCTIONS
CAUTION
³Inspect the wire insulation for any cuts, abrasions, or exposed copper that may have resulted during shipping. If there is a defect in the wire, do not attempt installation.
TOOLS REQUIRED
³Before starting installation of this fixture or removal of a previous fixture, disconnect the power by turning off the circuit breaker or by
removing the fuse at the fuse box.
Ladder
Safety glasses
Electrical Phillips
tape
screwdriver
Flat blade screwdriver
Pliers
Wire strippers
HARDWARE INCLUDED
Fixture
Mounting Unit
Screws
Mounting Screws
Wire Nuts
*PARTS SHOWN MAY DIFFER SLIGHTLY PER LIGHT FIXTURE
EXPLODED PARTS
INSTALLATION
Wire Nuts
Screws
STEP 1
Unscrew the ball nuts from the mounting unit. Use the mounting screws to attach the mounting unit to the junction box(not included).
Mounting Unit Mounting Screws
Fixture
Bulbs (not included)
STEP 2
Make the electrical connection from the junction box to the fixture. Connect the ground wire to the mounting unit using the preinstalled green ground screw. Then, connect the positive, negative and ground wires with the supplied wire nuts. Secure with electrical tape.
Black or Red wire (hot) from the junction box
White wire (neutral) from the junction box
Bare or Green ground wire from the junction box
*Sealing tape (not included)
Black wire from the fixture
White wire from the fixture
Ground wire from the Fixture
*Green Ground Screw
ASSEMBLY INSTRUCTIONS INSTALLATION
STEP 3
Attach the fixture to the mounting unit through screw holes as shown, and secure it with screws.
NOTICE: Please use caulk in the back plate and wall mounting surface to prevent water from entering.
STEP 4
Install bulbs (not included).
OPERATING INSTRUCTIONS
1. Light control switch is an automatic controller, can be used for outdoor and indoor light control automatic lighting, when the night comes illuminance 10Lux, the lamp will be automatically lit, and in the day when the illumination 30Lux, the lamp will automatically turn off the lamp.
illuminance 10Lux
illuminance 30Lux
2. Rated voltage: 120VAC/60Hz; The bulb should be installed at less than the rated power of the sensor; Energy-saving lamp/ballast /LED 39W; Incandescent lamp 100W.
LED LED
39W
100W
3. The photosensor should be installed in a place with good photosensitivity, without obstacles affecting its acceptance of natural light, and backlit with the lamp source, so as to prevent the product from jumping when sensing its own light.
4. There should be no swinging objects in front of the photosensor.
