Minka Lavery 2542-726 Park 11 Inch 2 Light Coal And Soft Brass Transitional Vanity Light Bar Instruction Manual

2542-726 Park 11 Inch 2 Light Coal and Soft Brass Transitional Vanity Light Bar

Product Information

This product is a light fixture with the item number 2542-726.
The installation instructions were last updated on February 18,
2022. Please read and save these instructions for future
reference.

Installation Instructions

WARNING! Before starting the installation
process, make sure to shut off power at the fuse box or circuit
breaker.

AVERTISSEMENT! Couper le courant au niveau des
fusibles ou du disjoncteur.

MOUNTING THE FIXTURE (Fig. 1)

1. Shut off power at the fuse box or circuit breaker box and
   remove the old fixture including the mounting hardware.
2. Carefully unpack your new fixture and lay out all the parts in
   a clear area. Take care not to misplace any small parts necessary
   for installation.
3. Thread all thread (E) into crossbar (C). Note: The length of
   all thread (E) into crossbar (C) may be adjusted if necessary.
4. Secure all thread (E) to crossbar (C) using lock washer (B) and
   hex nut (A).
5. Take this crossbar assembly (C) and mount it to the outlet box
   (not included) with mounting screws (D) (Size: #8-32N*L0.5). The
   side of crossbar marked with GND must face out.

CONNECTING THE WIRES (Fig. 2)

6. Connect the electrical wires as shown in Fig. 2, making sure
   that all wire connectors are secured. If your outlet box has a
   ground wire (green or bare copper), connect the fixture’s ground
   wire to it. Otherwise, connect the fixture’s ground wire directly
   to the crossbar (C) using the green screw provided. After the wires
   are connected, tuck them carefully inside the outlet box.

COMPLETING THE INSTALLATION (Fig. 1)

7. Place fixture body (F) over all thread (E) and secure with
   finial (G).
8. Install (2) two medium base T10 bulbs (I) up to 60 watts each
   or CFL or LED equivalent (not included) in accordance with the
   fixture specification. DO NOT EXCEED THE MAXIMUM WATTAGE RATING!
   (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!)
9. Place glass shade (J) over socket (H).

Your installation is now complete. Return power to the junction
box and test the fixture.

Note: The illustration (Fig. 1) in this manual
is for installation purposes only. It may or may not be identical
to the fixture purchased.

Wire Connections

LA-3510E

INSTALLATION INSTRUCTIONS

Item#2542-726 (New. 02/18/2022) READ AND SAVE THESE INSTRUCTIONS
W ARNING! SHUT POWE R OFF AT FUSE O R CIRCUIT BRE AKER.

AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.

MOUNTING THE FIXTURE (Fig. 1) 1. Shut off power at the fuse box or circuit breaker box and Fig.1

remove the old fixture including the mounting hardware.

2. Carefully unpack your new fixture and lay out all the parts in a clear area. Take care not to misplace any small parts necessary for installation.
3. Thread all thread (E) into crossbar (C). Note: The length

Set# A-010 – Crossbar – Ground screw – Mounting Screw*2

of all thread (E) into crossbar (C) may be adjusted, if

necessary.

4. Secure all thread (E) to crossbar (C) using lock washer

(B) and hex nut (A). 5. Take this crossbar assembly (C) and mount it to outlet box
(not included) with mounting screws (D) (Size:

A

J

B

#8-32N*L0.5″). The side of crossbar marked with “GND” must face out.
CONNECTING THE WIRES (Fig. 2)
6. Connect the electrical wires as shown in Fig. 2, making

C

D

I

E

sure that all wire connectors are secured. If your outlet

box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the

H

fixture’s ground wire directly to the crossbar (C) using the

green screw provided. After the wires are connected, tuck

them carefully inside the outlet box.

F

COMPLETING THE INSTALLATION (Fig.1)

7. Place fixture body (F) over all thread (E) and secure with

finial (G)

G

8. Install (2) two medium base T10 bulb (I) up to 60 watts

each or CFL or LED equivalent (not included) in

accordance with the fixture specification — DO NOT

EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS Fig. 2

DEPASSER LA PUISSANCE NOMINALE MAXIMALE!). 9. Place glass shade (J) over socket (H).

FIXTURE WIRES Black or Smooth

FIXTURE WIRES White or Ribbed

FIXTURE WIRES Bare Copper (Ground)

Your installation is now complete. Return power to the junction box and test the fixture.
Note: Illustration (Fig. 1) on this manual is for installation purposes only. It may or may not be identical to the fixture purchased.

HOUSE WIRES Black (Hot)

HOUSE WIRES White (Neutral)

HOUSE WIRES Green (Ground)

LA-3510E