2431-84 Winsley 5.375 Inch 1-Light Coal and Stained Brass Vanity Light
Product Information
The product is a ceiling fixture with item number 2431-84/878.
It comes with a circular strap, ground screw, mounting screw,
finials, metal ring, glass shade, and socket cup. The fixture
requires one medium base (E26) bulb up to 60 watts or CFL or LED
equivalent (not included). The installation manual warns to not
exceed the maximum wattage rating.
Usage Instructions
- Turn off power at the fuse box or circuit breaker.
- Remove the old fixture and its mounting hardware.
- Unpack the new fixture and lay out all parts on a clean
area. - Thread mounting screws into pre-drilled holes in the circular
strap spaced the same distance apart as holes in the back plate.
Tighten with nuts. Adjust the length of mounting screws if
necessary. - Attach the circular strap to the junction box using junction
box screws. The side of the circular strap marked GND must face
out. Connect the electrical wires as shown in Fig.2, making sure
that all wire connectors are secured. If your junction box has a
ground wire, connect the fixture’s ground wire to it. Otherwise,
connect the fixture’s ground wire directly to the circular strap
using the green screw provided. Tuck wire connectors neatly into
the junction box. - Place back plate onto mounting screws and secure with finials.
Unscrew metal ring and place glass shade onto socket cup. Secure
glass shade with metal ring. - Install one medium base (E26) bulb up to 60 watts each or CFL
or LED equivalent (not included) in accordance with the fixture
specification. Do not exceed the maximum wattage rating. - Turn power back on at the junction box and test the
fixture.
Note: The illustration in the manual is for installation
purposes only and may or may not be identical to the fixture
purchased.
INSTALLATION INSTRUCTIONS
Item#2431-84/878 (New. 08/27/2021) READ AND SAVE THESE INSTRUCTIONS
W ARNI NG ! SHUT P OWE R O FF AT F US E O R CI RCUIT BRE AKE R.
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
MOUNTING THE FIXTURE (Fig.1) 1. Shut off power at the fuse box or circuit breaker and
remove the old fixture including the mounting hardware. 2. Carefully unpack your new fixture and lay out all the parts
on a clean area. Take care not to lose any small parts necessary for installation. 3. Thread mounting screws (B) into pre-drilled holes in circular strap (G) spaced same distance apart as holes in back plate and tighten with nuts (E). The length of mounting screws (B) may be adjusted if necessary. 4. Attach circular strap (G) to junction box (not included) using junction box screws (D). The side of circular strap marked “GND” must face out.
Fig.1
Set# A-021 -Circular Strap -Ground Screw -Mounting Screw*2
CONNECTING THE WIRES (Fig.2) 5. Connect the electrical wires as shown in Fig.2, making sure
that all wire connectors (C) are secured. If your junction box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the circular strap (G) using the green screw provided. 6. Tuck wire connectors neatly into the junction box.
FINISHING THE INSTALLATION (Fig.1) 7. Place back plate onto mounting screws (B) and secure
with finials (A). 8. Unscrew metal ring (F) and place glass shade (I) onto
socket cup (H). Secure glass shade (I) with metal ring (F). 9. Install (1) one medium base (E26) bulb up to 60 watts
each or CFL or LED equivalent (not included) in accordance with the fixture specification–DO NOT EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!).
Your installation is now complete. Return power to the junction box and test the fixture.
Note: Illustration (Fig.1) on this manual is for installation purposes only. It may or may not be identical to the fixture purchased.
Fig.2
FIXTURE WIRES Black or Smooth
FIXTURE WIRES White or Ribbed HOUSE WIRES Black (Hot)
FIXTURE WIRES Green or Bare Copper (Ground) HOUSE WIRES White (Neutral)
HOUSE WIRES Green (Ground)
2431-84/878
