Minka Lavery 2732-709 Graham Avenue 13.5 Inch 2 Light Smoked Iron And Brushed Nickel Vanity Light Instruction Manual

2732-709 Graham Avenue 13.5 Inch 2 Light Smoked Iron and Brushed Nickel Vanity Light

Product Information

The product being installed is Item#2732-709, a fixture that is
intended to be wall-mounted. The installation manual is dated
February 17, 2022. The product comes with a mounting plate, two
mounting screws, a ground screw, and a metal ring to secure the
glass shade. The fixture can accommodate two candelabra base bulbs
of up to 60 watts each or CFL or LED equivalent (not included).

Product Usage Instructions

1. Shut off power at the fuse box or circuit breaker box.
2. Remove the old fixture including the mounting hardware.
3. Unpack the new fixture and lay out all the parts in a clear
   area. Take care not to misplace any small parts necessary for
   installation.
4. Loosen screws (D) to remove mounting plate (A) from fixture
   body (C).
5. Position mounting plate (A) on the wall and mark the location
   of four drywall anchors (I). Pre-drill the holes for the drywall
   anchors (I). Insert the drywall anchors (I) into the wall.
6. Attach mounting plate (A) to junction box (not included) with
   mounting screws (B) (Size: #8-32N*L0.5). The side of the mounting
   plate (A) marked GND and two convex points must face out.
7. If your junction box has a ground wire (green or bare copper),
   connect the fixture’s ground wire to it. Otherwise, connect the
   fixture’s ground wire directly to the mounting plate (A) using the
   green screw provided.
8. Place fixture body (C) over mounting plate (A) and secure with
   screws (D).
9. Place glass shade (F) over socket (E) and secure with metal
   ring (G).
10. Install (2) two candelabra base bulbs (H) up to 60 watts each
    or CFL or LED equivalent (not included) in accordance with the
    fixture specification — DO NOT EXCEED THE MAXIMUM WATTAGE RATING!
    (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!)
11. Return power and test the fixture.

INSTALLATION INSTRUCTIONS

Item#2732-709 (New. 2022/02/17) READ AND SAVE THESE INSTRUCTIONS
W AR N I N G ! S HU T P O WE R O F F AT F U S E O R CI R C UI T B R E AK E R .
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.

MOUNTING THE FIXTURE (Fig.1)

Fig. 1

1. Shut off power at the fuse box or circuit breaker box

and remove the old fixture including the mounting hardware. 2. Carefully unpack your new fixture and lay out all the

Set#A-021-170118A -Mounting screw*2
-Ground screw -Mounting plate

parts in a clear area. Take care not to misplace any

small parts necessary for installation.

I

3. Loosen screws (D) to remove mounting plate (A) from

fixture body (C).

4. Position mounting plate (A) on the wall and mark the

location of four drywall anchors (I). Pre-drill the holes

for the drywall anchors (I). Insert the drywall anchors

(I) into the wall.

5. Attach mounting plate (A) to junction box (not included)

with mounting screws (B) (Size: #8-32N*L0.5″). The

side of the mounting plate (A) marked “GND” and two

convex points must face out.

6. Place woodscrews (J) through holes into the drywall

anchor (I) to secure the mounting plate (A) as shown in

Fig.1.

CONNECTING THE WIRES (Fig. 2)

7. Connect the electrical wires as shown in Fig. 2, making

sure that all wire connectors are secured. If your

junction box has a ground wire (green or bare copper),

connect the fixture’s ground wire to it. Otherwise,

connect the fixture’s ground wire directly to the

mounting plate (A) using the green screw provided.

After the wires are connected, tuck them carefully

inside the junction box.

FINISHING THE INSTALLATION (Fig.1) 8. Place fixture body (C) over mounting plate (A) and
secure with screws (D). 9. Place glass shade (F) over socket (E) and secure with

Fig. 2
FIXTURE WIRES Black or Smooth

FIXTURE WIRES White or Ribbed

metal ring (G).

10. Install (2) two candelabra base bulbs (H) up to 60

watts each or CFL or LED equivalent (not included) in accordance with the fixture specification — DO NOT

HOUSE WIRES Black (Hot)

EXCEED THE MAXIMUM WATTAGE RATING! (NE

PAS DEPASSER LA PUISSANCE NOMINALE

MAXIMALE!)

Your installation is now complete. Return power and

test the fixture.

A J

B

D

C

E F

G H

FIXTURE WIRES Green or Bare Copper (Ground)

HOUSE WIRES White (Neutral)

HOUSE WIRES Green (Ground)

Note: Illustration (Fig.1) on this manual is for installation purposes only. It may or may not be identical to the fixture purchased.

LA-3521E