Minka Lavery 2894-691 Pullman Junction 29 Inch 4 Light Brushed Nickel And Coal Vanity Light Instruction Manual

2894-691 Pullman Junction 29 Inch 4 Light Brushed Nickel and Coal Vanity Light

Product Information: Item#2894-691

The product is a fixture that requires installation. The package
includes mounting hardware, a mounting plate, screws, drywall
anchors, candelabra base bulbs (not included), and glass shades.
The fixture is compatible with CFL or LED equivalent bulbs up to 60
watts each. The fixture has three wires – black or smooth, white or
ribbed, and green or bare copper for ground. The product is
designed to be mounted on a wall and connected to a junction
box.

Product Usage Instructions

1. Shut off power at the fuse box or circuit breaker box and
   remove the old fixture including the mounting hardware.
2. Carefully unpack the new fixture and lay out all the parts in a
   clear area. Take care not to misplace any small parts necessary for
   installation.
3. Loosen screws (E) to remove mounting plate (A) from fixture
   body (F).
4. Position mounting plate (A) on the wall, and mark the location
   of two drywall anchors (B). Pre-drill the holes for the drywall
   anchors (B). Insert the drywall anchors (B) into the wall.
5. Attach the mounting plate (A) to the junction box (not
   included) using the mounting screws (D). The side of the mounting
   plate (A) marked GND must face out.
6. Screw woodscrews (C) through the holes into the drywall anchor
   (B) to secure the mounting plate (A).
7. Connect the electrical wires as shown in Fig. 2, making sure
   that all wire connectors are secured. If your junction box has a
   ground wire (green or bare copper), connect the fixture’s ground
   wire to it. Otherwise, connect the fixture’s ground wire directly
   to the mounting plate (A) using the green screw provided. After the
   wires are connected, tuck them carefully inside the junction
   box.
8. Slide fixture body (F) over mounting plate (A) and secure with
   screws (E).
9. Install (4) four candelabra base bulbs (H) up to 60 watts each
   or CFL or LED equivalent (not included) in accordance with the
   fixture specification. Do not exceed the maximum wattage
   rating.
10. Screw glass shades (I) onto socket cups (G).
11. Turn on power and test the fixture.

Note: Illustration (Fig.1) on this manual is for installation
purposes only. It may or may not be identical to the fixture
purchased.

INSTALLATION INSTRUCTIONS

Item#2894-691 (New. 2021/8/18) READ AND SAVE THESE INSTRUCTIONS
W AR N I N G ! S HU T P O WE R O F F AT F U S E O R CI R C UI T B R E AK E R .
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.

MOUNTING THE FIXTURE (Fig.1)

Fig. 1

1. Shut off power at the fuse box or circuit breaker box

and remove the old fixture including the mounting hardware. 2. Carefully unpack your new fixture and lay out all the

Set#A-021-700117A -Mounting Screw*2
-Ground Screw -Mounting Plate

parts in a clear area. Take care not to misplace any

small parts necessary for installation.

3. Loosen screws (E) to remove mounting plate (A) from

fixture body (F).

4. Position mounting plate (A) on the wall, and mark the

location of two drywall anchors (B). Pre-drill the holes

for the drywall anchors (B). Insert the drywall anchors

(B) into the wall.

5. Attach the mounting plate (A) to the junction box (not

included) using the mounting screws (D). The side of

the mounting plate (A) marked “GND” must face out.

6. Screw woodscrews (C) through the holes into the

drywall anchor (B) to secure the mounting plate (A) as

shown in Fig.1.

CONNECTING THE WIRES (Fig. 2)

7. Connect the electrical wires as shown in Fig. 2, making

sure that all wire connectors are secured. If your

junction box has a ground wire (green or bare copper),

connect the fixture’s ground wire to it. Otherwise,

connect the fixture’s ground wire directly to the

mounting plate (A) using the green screw provided.

After the wires are connected, tuck them carefully

inside the junction box.

FINISHING THE INSTALLATION (Fig.1)

8. Slide fixture body (F) over mounting plate (A) and
secure with screws (E).
9. Install (4) four candelabra base bulbs (H) up to 60
watts each or CFL or LED equivalent (not included) in accordance with the fixture specification. –DO NOT

Fig. 2
FIXTURE WIRES Black or Smooth

FIXTURE WIRES White or Ribbed

EXCEED THE MAXIMUM WATTAGE RATING! (NE

PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!)

HOUSE WIRES Black (Hot)

10. Screw glass shades (I) onto socket cups (G).

B A

C E F

D G

H

I

FIXTURE WIRES Green or Bare Copper (Ground)

HOUSE WIRES White (Neutral)

HOUSE WIRES Green (Ground)

Your installation is now complete. Return power and test the fixture.
Note: Illustration (Fig.1) on this manual is for installation purposes only. It may or may not be identical to the fixture purchased.

LA-3458E