Mountup Mp0006 Triple Monitor Counterbalance Desk Mount Instruction Manual

MP0006 Triple Monitor Counterbalance Desk Mount

Product Information:

Product Usage Instructions:

WARNING!

If you have any confusions or are not quite sure about the
installation, please do not hesitate to ask for our help.

Before assembly, please check and make sure all necessary
accessories are included and undamaged. Improper installation, such
as using the product for monitors over its load capacity or for any
purpose not explicitly specified, may cause damage or serious
injury. We would not be liable for any damage or injury caused by
improper mounting or inappropriate use.

The kit contains small items that could be choking hazards if
swallowed. Please keep them out of reach of children under 3 years
old. Adult supervision is required.

Package Contents:

• A (x1) Arm
• B (x1) Clamp
• Clip Plate B2
• Bolt Y B4
• Bracket B1
• Bottom Plate B3
• Bolts B5
• C (x1) Decorative cover
• D (x3) VESA Plate
• E(x1) Middle Head
• F(x1) Pole
• G (x1) Wire clip
• L(x1) 4mm Allen Key
• H (x3) Bolt
• I (x3) Bolt
• J (x1) Support Plate
• K (x1) Grommet Base
• M(x1) 5mm Allen Key
• N(x1) 6mm Allen Key
• M-A (x12) M4x12mm Bolts
• M-B (x12) M4x25mm Bolts
• M-C (x12) Spacer H10mm

Assembly Steps:

Step 1: Clamp Installation OR Grommet Base Installation

OPTION A: Clamp Installation

1. Loosen Bolts (B5) by using 6mm Allen Key (N), then lift clip
   plate (B2), bottom plate (B3), and bolt Y (B4) a little to release
   them from bracket (B1).
2. Mount bracket (B1) to pole(F) using bolts (I). Tighten using
   4mm Allen Key (L).
3. Attach clip plate(B2), bottom plate(B3), bolt Y(B4) to bracket
   (B1) using bolts (B5) and 6mm Allen Key (N). Mount according to the
   thickness of the desktop.
4. Attach decorative cover (C) to pole(F) and secure the stand to
   the desktop by tightening clamp (B). Tighten bolt Y (B4) or by
   using 6mm Allen Key (N).

OPTION B: Grommet Base Installation

1. Use 6mm Allen Key (N) to detach the bolt (B5), clip plate (B2),
   bottom plate (B3), and bolt Y (B4) from clamp (B).
2. Install the grommet base plate (K) to the pole (F) using bolt
   (I).
3. Install pole(F) with bolt Y(B4) and support plate(J). Tighten
   bolt Y (B4) or by using 6mm Allen Key (N).

Step 2: Arm Installation

1. Install the middle head(E), wire clip(G), and swivel arm(A) to
   the pole. Fasten the bolt with supplied 6mm Allen Key (N). Please
   do not over tighten it in case the cast aluminum part could be
   damaged.

Step 3: Attach Monitor

OPTION A: Flat Back Monitor

1. Attach the VESA plate (D) to the back of the monitor and secure
   it by using a 6mm Allen Key (N) to tighten screws (M-A). Do not
   tighten the screws excessively or your monitor might be
   damaged.

OPTION B: Curved Back Monitor

1. Attach the VESA plate (D) to the back of the monitor and secure
   it by using a 6mm Allen Key (N) to tighten screws (M-B) along with
   spacers (M-C).

Triple Monitor Counterbalance Desk Mount
Instruction Manual

75x75mm 100x100mm

(1~8kg)x3 (2.2~17.6lbs)x3

If you have any questions , please contact our customer service.

TPM-MA02-36P-US2.0

WARNING!

If you have any confusions or are not quite sure about the installation, please do not hesitate to ask for our help.
Before assembly, please check and make sure all necessary accessories are included and undamaged. Improper installation, such as use the product for monitors over its load capacity or for any purpose not explicitly specified, may cause damage or serious injury. We would not be liable for any damage or injury caused by improper mounting or inappropriate use.
The kit contains small items that could be choking hazards if swallowed. Please keep them OUT OF REACH OF CHILDREN UNDER 3 YEARS OLD. ADULT SUPERVISION IS REQUIRED.

PACKAGE CONTENTS

All are included in B

A (x1) Arm

B (x1) Clamp

Clip Plate B2

Bolt Y B4

Bracket B1

Bottom Plate

Bolts

B3

B5

C (x1) Decorative cover

D (x3) VESA Plate

E(x1) Middle Head

F(x1) Pole

G (x1) Wire clip
L(x1) 4mm Allen Key

H (x3) Bolt

I (x3) Bolt

J (x1) Support Plate

K (x1) Grommet Base

M(x1) 5mm Allen Key

N(x1) 6mm Allen Key

M-A (x12) M4x12mm

M-B (x12) M4x25mm

(1~8kg)x3 (2.2~17.6lbs)x3
DO NOT EXCEED WEIGHT CAPACITY.
01

M-C (x12) Spacer H10mm
NOTE: Not all hardware included will be used.

ASSEMBLY STEPS
STEP 1 : Clamp Installation OR Grommet Base Installation
OPTION A: Clamp Installation Loosen Bolts (B5) by using 6mm Allen Key (N), then lift clip plate (B2), bottom plate (B3), and bolt Y (B4) a little to release them from bracket (B1).

35-80mm 10-45mm

B1
B5 N

B2 B3
B4

Mount bracket (B1) to pole(F) using bolts (I). Tighten using 4mm allen key(L). Attach clip plate(B2), bottom plate(B3), bolt Y(B4), to bracket (B1) using bolts (B5) and 6mm allen key (N). Mount according to the thickness of desktop.

F

B1

B2 B1

B2

B1

B5

B5

B3

I

B3

N

B4 N

B4

L

Decorative cover (C) to pole(F) and secure stand to desktop by tightening clamp (B). Tighten bolt Y (B4) or by using 6mm allen key (N).
F

C

B N
B4
02

STEP 1 : (Continued)
OPTION B: Grommet Base Installation Use 6mm allen key(N) to detach the bolt(B5), clip plate(B2),bottom plate(B3) and bolt Y(B4) from clamp(B).

DESK
ø 0.39~2.36″ ø 10~60mm
DESK

B2 B1

B5

B3

N

B4

Install the grommet base plate(K) to the pole (F) using bolt (I). Install pole(F) with bolt Y(B4) and support plate(J). Tighten bolt Y (B4) or by using 6mm allen key (N).

10-80mm

F I B4
K
J
B4 N
03

STEP 2 : Arm Installation
Install the middle head(E), wire clip(G) and swivel arm(A) to the pole. Fasten the bolt with supplied 6mm Allen key (N)
E G
A
Just tighten the bolt, do not over tighten it in case the cast aluminum part could be damaged.
N

DESK

DESK

Please do not move stand outside desk for safety!

04

STEP 3: Attach Monitor
OPTION A: Flat Back Monitor
Attach the VESA plate (D) to the back of monitor and secure it by using a 6 mm Allen Key (N) to tighten screws (M-A).
Do not tighten the screws excessively or your monitor might be damaged.
D

Monitor

Monitor Monitor

N M-A

OPTION B: Curved Back Monitor
Attach the VESA plate (D) to the back of monitor and secure it by using a 6 mm Allen Key (N) to tighten screws (M-B) along with spacers (M-C).
Do not tighten the screws excessively or your monitor might be damaged.
D
05

monitor

monitor monitor

N M-B
M-C

STEP 4 : Hang Monitor
Slide the monitors onto the head of swivel arm.Install the security bolt (H). Make sure the security bolt is installed before you rotate the monitor.

H

Important Notice: The gas spring is pre-set to minimum tension. Once the monitor is hanged on, hold the monitor with both hands and DO NOT let go suddenly or immediately. Instead, leave the monitor in a slow & gentle way while observing whether the arms will fall down wildly.
Guideline to adjust monitor tilting angle.
Problem: If monitor face down

N
06

Solution: 1. Loosen the tilting bolt.
2. Hold the bottom of monitor with one hand and adjust to determine your desired tilt angle.
3. Retighten the tilting bolt to fix the intended angle.

STEP 5 : Adjust Tension
For intended functioning of the mount, you may need to adjust the tension of Upper Arm (A) in accordance with your monitor weight by 6 mm Allen Key (N).

N A

CAUTION
Note1:
Be sure to keep the arm in horizontal position during adjustment. Or else it would be difficult to adjust the mount or damage the mount.
Situation 1: Arm falls down Upper Arm with monitor falls down and fails to stay where intended.
Solution: Turn the inside screw counterclockwise(“+”direction) to increase gas spring tension until the arm can stay as intended.

Situation 2: Arm rises up Upper Arm with monitor rises up and fails to stay where intended.
Solution: Turn the inside screw clockwise(“-“direction) to decrease gas spring tension until the arm can stay as intended.

Note2:
For how many circles the screw should be turned, please refer to the table below.

Monitor Weight

1kg 2kg 3kg 4kg 5kg 6kg

Circles (AT LEAST) min 1

2

5

7

10

07

7kg 8kg 13 15

STEP 6 : Cable Management
Remove bottom plastic covers from gas spring arm (A) .Run cables from monitor through bottom of arm. Reattach plastic covers as shown in diagram. Store Allen keys (M,N) in wire clip (G) for future use.
N M
G
A
08

Adjust as Desired
Adjust monitor position and rotation.

Swivel ±90°

Swivel ±180°

Tilt Swivel Rotation Height
Note: To ensure stability, the tightness of the rotating axis has been preset, so it would be kind of difficult to rotate the VESA plate. Suggestion: Please attach the monitor first, then hold the two sides of it with both hands, and rotate vigorously. If that doesn’t work out, please do not hesitate to ask for our help.

±90° Swivel

Rotation
360°

+35° Tilt -35°

Height

183cm

Note: The total length of 3 monitors after arrayed can not be longer than 183cm.

–

M
+

09

If necessary, refer to above illustrations to adjust the level of tightness of the arms.

Product Dimensions

±90° 1.7″

±180° 7.9″

±180° 7.9″

±90° 8.1″-10.3″ 2.67″

2.9″ 3.9″ 4.48″
±180°

2.9″ 3.9″ 4.48″

11.5″

+90° -45°

16.5″

4.5″-27.8″

0.39″-3.15″ 0.39″-3.15″

5.7”

10

CAUTION AND MAINTENANCE:
· Don’t allow children to climb, stand, hang, or play on any part of monitor or stand. · This product is intended for indoor use only. Using this product outdoors could lead to
product failure and personal injury. · Check that the bracket is secure and safe to use at regular intervals (at least every three months).