American Express Ahp-63 Triple Monitor Counterbalance Desk Mount Instruction Manual

AHP-63 Triple Monitor Counterbalance Desk Mount

Product Information:

Product Usage Instructions:

WARNING!

If you have any confusions or are not quite sure about the
installation, please do not hesitate to ask for our help.

Before assembly, please check and make sure all necessary
accessories are included and undamaged. Improper installation, such
as using the product for monitors over its load capacity or for any
purpose not explicitly specified, may cause damage or serious
injury. We would not be liable for any damage or injury caused by
improper mounting or inappropriate use.

The kit contains small items that could be choking hazards if
swallowed. Please keep them OUT OF REACH OF CHILDREN UNDER 3 YEARS
OLD. ADULT SUPERVISION IS REQUIRED.

Package Contents:

Assembly Steps:

STEP 1: Apply Pads To The Base Bottom

Paste the Pad (F1) onto the Base (F).

STEP 2: Clamp Installation Or Grommet Base Installation

OPTION A: Clamp Installation

Loosen Bolts (B4) by using 5mm Allen Key (I). Then align the
screw hole on the Base (F), and lock the Screw (B4) with a 5mm
Allen Key (I).

OPTION B: Grommet Base Installation

Detach Clip Plate (B2) and Bolt Y (B3) from Clamp (B). Use Bolt
Y (B3) through the screw hole on Bracket (B1) to fix the Base (F)
and the table board together.

STEP 3: Arm Installation

Install the Middle Head (E), Wire Clip (G), and swivel Arm (A)
on the base in sequence. Fasten the bolt with the supplied 6mm
Allen Key (J).

STEP 4: Attach Monitor

OPTION A: Flat Back Monitor

Attach the VESA Plate (D) to the back of the monitor and secure
it with Screws (M-A) and Washers (M-C) using a 5mm Allen Key
(I).

OPTION B: Curved Back Monitor

Attach the VESA Plate (D) to the back of the monitor and secure
it with Screws (M-B), Washers (M-C), and Spacer (M-D) using a 5mm
Allen Key (I).

STEP 5: Hang Monitor

Slide the monitor onto the head of the swivel arm. Install the
Security Bolt (H). Make sure the security bolt is tightened before
you rotate the monitor.

Important Notice: Once the monitor is hanged
on, hold the monitor with both hands and DO NOT let go suddenly or
immediately. Instead, leave the monitor in a slow & gentle way
while observing whether the arms will fall down wildly.

Triple Monitor Counterbalance Desk Mount
Instruction Manual

75×75 100×100

27″

(2~9kg)x3 (4.4~19.8lbs)x3

If you have any questions, please feel free to contact our customer service via Amazon.

AHP-63-US1.0

WARNING!
If you have any confusions or are not quite sure about the installation, please do not hesitate to ask for our help.
Before assembly, please check and make sure all necessary accessories are included and undamaged. Improper installation, such as use the product for monitors over its load capacity or for any purpose not explicitly specified, may cause damage or serious injury. We would not be liable for any damage or injury caused by improper mounting or inappropriate use.
The kit contains small items that could be choking hazards if swallowed. Please keep them OUT OF REACH OF CHILDREN UNDER 3 YEARS OLD. ADULT SUPERVISION IS REQUIRED.
PACKAGE CONTENTS
All are included in B

A (x1) Arm

A1 (x2) Harness Cover

Clip Plate B2

B (x1) Clamp

Bracket B1

Bolts B4(x2)

Bolt Y B3

C (x1)

D (x3)

Decorative Cover VESA Plate

E(x1) Middle Head

E1(x2) Plastic Spacer

F(x1) Base

F1(x3) Pad

G (x1) Wire Clip

H (x3) Bolt

I(x1) 5mm Allen Key

J(x1) 6mm Allen Key

M-A (x12) M4x12mm

M-B (x12) M4x30mm

M-C (x12 ) D5 Washer

M-D (x24) Spacer H5mm

(4.4~19.8lbs)x3 (2~9kg)x3
DO NOT EXCEED WEIGHT CAPACITY.

NOTE: Not all hardware included will be used.
01

ASSEMBLY STEPS
STEP 1: Apply Pads To The Base Bottom
Paste the Pad (F1) onto the Base (F)
F1
F

STEP 2: Clamp Installation Or Grommet Base Installation
OPTION A: Clamp Installation Loosen Bolts (B4) by using 5mm Allen Key (I)Then align the screw hole on the Base (F), and then lock the Screw (B4) with a 5mm Allen Key (I).
I
F
B

Fix the Decorative Cover (C) to the Base (F) and fix the bracket on the table by tightening the Clamp (B).

C F

Min10mm~Max50mm

Don’t over tightened

02

STEP 2: (Continued)
OPTION B: Grommet Base Installation Detach Clip Plate(B2)and Bolt Y(B3) from Clamp(B).
B4 B2

B1

B3

Use Bolt Y (B3) through the screw hole on Bracket (B1) to fix the Base (F) and the table board together.

F Min10mm~Max50mm B1 B3
03

STEP 3 : Arm Installation
Install the Middle Head(E), Wire Clip(G) , swivel Arm(A) on the base in sequence as shown below. Fasten the bolt with supplied 6mm Allen Key (J)
E1 E
E A
G J
J
04

STEP 4 : Attach Monitor
OPTION A: Flat Back Monitor
Attach the VESA Plate (D) to back of monitor and secure with Screws(M-A) with Washers(M-C ) using 5 mm Allen Key (I). Avoid excessive tightening screws damage the monitor.

UP

D

I
M-A M-C

OPTION B: Curved Back Monitor
Attach the VESA Plate (D) to back of monitor and secure with Screws (M-B) with Washers (M-C)and Spacer(M-D)using 5 mm Allen Key (I). Avoid excessive tightening screws damage the monitor.
UP D
NOTE: Hand tighten screws to avoid over tightening.
05

I M-B M-C
M-D
one or two piece

STEP 5 : Hang Monitor
Slide the monitor onto the head of swivel arm.Install the Security Bolt (H). Make sure the security bolt is tightened before you rotate the monitor.
H

Important Notice:
Once the monitor is hanged on, hold the monitor with both hands and DO NOT let go suddenly or immediately. Instead, leave the monitor in a slow & gentle way while observing whether the arms will fall down wildly.
Refer to below illustrations to adjust tilting angle of your monitor.

I
06

Problem: If monitor face down
Solution: 1. Loosen the tilting bolt. 2. Hold the bottom of monitor with one hand and adjust to determine your desired tilt angle. 3. Retighten the tilting bolt to fix the intended angle.

STEP 6 : Adjust Tension
For intended functioning of the mount, you may need to adjust the tension of Arm (A) in accordance with your monitor weight by 6 mm Allen Key (J).
J

CAUTION
Note1:
Be sure to keep the arm in horizontal position during adjustment.

Situation 1: Arm falls down Upper Arm with monitor falls down and fails to stay where intended. Solution: Turn the inside screw counterclockwise(“+”direction) to increase gas spring tension until the arm can stay as intended.
Situation 2: Arm rises up Upper Arm with monitor rises up and fails to stay where intended.
Solution: Turn the inside screw clockwise(“-“direction) to decrease gas spring tension until the arm can stay as intended.

Note2:
For how many circles the screw should be turned, please refer to the table below.

(AT LEAST) min 2

46
07

8 10 12 15

STEP 7 : Cable Management
Remove bottom plastic covers from gas spring Arm (A) .Run cables from monitor through bottom of gas spring Arm (A). Then cover the Wire Cap (A1) onto the upper arm of the Arm (A). Reattach plastic covers as shown in diagram.

Insert
A1

Press

Press

Insert

Push and Slide Remove the harness cap
08

Insert and Push

Adjust as Desired
Note: The total length of 3 monitors after arrayed can not be longer than 183cm.
Adjust monitor position and rotation.
Tilt Swivel Rotation

Swivel
±90°

±180° Rotation

+90° Tilt -90°

Swivel ±180°

Swivel ±135°

Swivel
±90°

±180°

±135° Swivel
I J

DESK

Note: To ensure stability, the tightness of the rotating axis has been preset, so it would be kind of difficult to rotate the VESA plate. Suggestion: Please attach the monitor first, then hold the two sides of it with both hands, and rotate vigorously. If that doesn’t work out, please do not hesitate to ask for our help.
09

DESK
Please do not move stand outside desk for safety!

max290mm

Product Dimensions
+90°
Tilt
-90°

2.95″ 75mm
3.94″ 100mm
4.5″ 114mm

752.m95m” 1030.9m4″m
1144.5m”m

±180°

Swivel
180°
min1256mm~max1376mm
60mm
min215~max275mm

183mm

47mm

35mm

183mm

Swivel ±135°

25mm min10mm~max50mm

407mm

Swivel ±135°
25mm
Min10mm ~Max50mm

10

CAUTION AND MAINTENANCE:
· Never allow children to climb, stand, hang, or play on any part of monitor or stand. · This product is intended for indoor use only. Using this product outdoors could
lead to product failure and personal injury. · Check that the bracket is secure and safe to use at regular intervals
(at least every three months).