V I V O Stand-v103 Triple Monitor Desk Mount Instruction Manual (+ PDF)

Contents hide

2 Product Information: Triple Monitor Desk Mount

STAND-V103 Triple Monitor Desk Mount

Product Information: Triple Monitor Desk Mount

The Triple Monitor Desk Mount is a sturdy and versatile mount
that can hold up to three monitors at once. It comes with a pole,
upper and lower clamps, arm extensions, joint covers, plastic
spacers, a support plate center VESA plate, side VESA plates,
grommet pad, cable clips, spare caps, screws, cap nuts, and
wrenches. The mount has a weight capacity of 22 lbs per arm or 10
kg.

Product Usage Instructions

Option A: Clamp Installation
1. Install the upper clamp (C) to the pole (A) using M6x8mm screws
  (S-A) and a Phillips screwdriver.
2. Assemble the lower clamp (B) to the upper clamp (C) using
  M10x15mm screws (S-B) and a 5mm Allen wrench (T-B).
3. Secure the clamp assembly to the desktop by tightening the hand
  bolts on the lower clamp (C).
4. Install the pole cover (D) to the pole (A).
Option B: Existing Grommet Base Installation
1. Remove the adhesive backing from the grommet pad (L) and place
  it on the bottom of the pole (A).
2. Install the pole (A) to an existing grommet hole using the
  support plate (I) with an M10 bolt (S-F), M10 washer (S-E), and
  lock washer (S-G). Tighten with wrench (T-D).
3. Install the pole cover (D) to the pole (A).
Option C: Self-Drilled Grommet Base
Installation
1. Drill a 3/8 (10mm) diameter hole through the mounting
  surface.
2. Remove the adhesive backing from the grommet pad (L) and place
  it on the bottom of the pole (A).
3. Install the pole (A) to an existing grommet hole using the
  support plate (I) with an M10 bolt (S-F), M10 washer (S-E), and
  lock washer (S-G). Tighten with wrench (T-D).
4. Install the pole cover (D) to the pole (A).
Align arm extensions (F) with arm (E) so that the holes for the
wire clips are facing down. Place plastic spacers (H) on top and
bottom of arm extensions (F). Assemble arm extensions (F) to arm
(E) with M10x47mm screws (S-C) and tighten using 6mm Allen wrench
(T-C). Press joint covers (G) into place.
Assemble arm (E) to pole (A) using M8x10mm screws (S-D) and 5mm
Allen wrench (T-B).
Option A: Flat Back Monitor
1. Secure side VESA plates (K) to monitors using M4x12mm
  thumbscrews (M-A).
Option B: Curved Back Monitor
1. Secure side VESA plates (K) to monitors using M4x30mm screws
  (M-B) and M4 spacers (M-C).

Warning: Do not exceed weight capacity. Failure
to do so may result in serious injury. This product is not suitable
for children under 3 years of age due to small parts. Adult
supervision is required.

View Fullscreen

Triple Monitor Desk Mount
Instruction Manual

SKU: STAND-V103
Scan the QR code with your mobile device or follow the link for helpful videos and specifications related to this product. https://vivo-us.com/products/stand-v103
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

[email protected]

www.vivo-us.com Chat live with an agent!

309-278-5303

WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER: · NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND. · USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
PACKAGE CONTENTS

A (x1) Pole

B (x1) Lower Clamp

C (x1) Upper Clamp

D (x1) Pole Cover

E (x1) Arm

F (x2) Arm Extension

G (x4) Joint Cover

H (x4) Plastic Spacer

I (x1)

J (x1)

Support Plate Center VESA Plate

K (x2) Side VESA Plate

L (x1) Grommet Pad

M (x4) Cable Clip

N (x2) Spare Cap

S-A (x3) M6x8mm
Screw

S-B (x2) M10x15mm
Screw

S-C (x2) M10x47mm
Screw

S-D (x2) M8x10mm
Screw

S-E (x1) M10 Washer

S-F (x1) M10 Bolt

S-G (x1) Lock Washer

M-B (x12) M4x30mm
Screw

M-C (x12) M4 Spacer

S-H (x1) M4x6mm
Screw

S-I (x2) Cap Nut

M-A (x12) M4x12mm Thumbscrew

T-A (x1) 3mm Allen
Wrench

T-B (x1) 5mm Allen
Wrench

T-C (x1) 6mm Allen
Wrench

T-D (x1) Wrench 2

NOTE: SOME HARDWARE MAY NOT BE USED

TOOLS NEEDED

Phillips

Drill

Screwdriver

DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.

22 lbs Per Arm (10 kg)

ASSEMBLY STEPS
STEP 1 OPTION A: Clamp Installation Install Upper Clamp (C) to Pole (A) using M6x8mm Screws (S-A) and a Phillips screwdriver. Assemble Lower Clamp (B) to Upper Clamp (C) using M10x15mm Screws (S-B) and 5mm Allen Wrench (T-B). Secure the clamp assembly to the desktop be tightening to the hand bolts on Lower Clamp (C). Install the Pole Cover (D) to Pole (A).

D S-A

S-B

T-B

OPTION B: Existing Grommet Base Installation Remove adhesive backing from Grommet Pad (L) and place on the bottom of Pole (A). Install Pole (A) to existing grommet hole using Support Plate (I) with M10 Bolt (S-F), M10 Washer (S-E) and Lock Washer (S-G). Tighten with Wrench (T-D). Install the Pole Cover (D) to Pole (A).

S-G

S-E

S-F

T-D

STEP 1 (Continued) OPTION C: Self-Drilled Grommet Base Installation Drill a 3/8″ (10mm) diameter hole through the mounting surface Remove adhesive backing from Grommet Pad (L) and place on the bottom of Pole (A). Install Pole (A) to existing grommet hole using Support Plate (I) with M10 Bolt (S-F), M10 Washer (S-E) and Lock Washer (S-G). Tighten with Wrench (T-D). Install the Pole Cover (D) to Pole (A).
A
L D

S-G

S-E

S-F

T-D

STEP 2 Align Arm Extensions (F) with Arm (E) so that the holes for the wire clips are facing down. Place Plastic Spacers (H) on top and bottom of Arm Extensions (F). Assemble Arm Extensions (F) to Arm (E) with M10x47mm Screws (S-C) and tighten using 6mm Allen Wrench (T-C). Press Joint Covers (G) into place.

T-C

S-C G

STEP 3 Assemble Arm (E) to Pole (A) using M8x10mm Screws (S-D) and 5mm Allen Wrench (T-B).
E
T-B S-D A

STEP 4

OPTION A: Flat Back Monitor

OPTION B: Curved Back Monitor

Secure Side VESA Plates (K) to monitors Secure Side VESA Plates (K) to monitors

using M4x12mm Thumbscrews (M-A). using M4x30mm Screws (M-B) and M4

Spacers (M-C).

M-A K

M-C K M-B

Secure Center VESA Plate (J) to monitors Secure Center VESA Plate (J) to monitors using M4x12mm Thumbscrews (M-A). using M4x30mm Screws (M-B) and M4
Spacers (M-C).
=

M-A J

M-C J M-B

STEP 5 Assemble side VESA Plates (K) with monitors to Arm Extensions (F). Secure using Cap Nuts (S-I).

Assemble Center VESA Plate (J) with monitor to Arm (E). Secure using M4x6mm Screw (S-H).

F K
S-I

J E
S-H

STEP 6 Remove the plastic covers on Arm Extensions (F) and adjust the tilt using Wrench (T-D).

Adjust the Tilt and rotation of the center monitor by loosening the set screw on Arm (E) using 3mm Allren Wrench (T-A). Retighten the set screw.
T-A

F E
T-D

STEP 7

Adjust the Height of Center Monitor: Adjust the Height of Side Monitors:

Using 6mm Allen Wrench (T-C), turn the Remove Cap Nut (S-I) from Arm Exten-

bolt on Arm (E) counterclockwise to

sions (F). Turn the screw using counter-

lower the center monitor, turn the bolt clockwise using 3mm Allen Wrench (T-A)

clockwise to raise the center monitor. to raise the monitor, and clockwise to

lower it.

T-A

T-C

STEP 8 Remove Joint Covers (G) from Arm (E) to adjust the tension using 6mm Allen Wrench (T-C).

T-C

STEP 9 Insert Cable Clips (M) into the undersides of Arm (E) and Arm Extensions (F). Route cables through Cable Clips (M) and Pole (A).
E F
M A
7

Love your new VIVO setup and want to share? Tag us in your photo! @vivo_us

LAST UPDATED: 06/13/2022 REV2

Open Monday – Friday 7:00am – 7:00pm CST, our dedicated support team can offer immediate assistance with rapid response times. If any parts are received damaged or defective, please contact us. We are happy to replace parts to ensure you have a fully functioning product.

309-278-5303

AVG. RESOLUTION TIME (within office hrs): 5M 4S

www.vivo-us.com
Chat live with an agent!

AVG. RESOLUTION TIME (within office hrs): < 15 M

[email protected]

AVG. RESPONSE TIME (within office hrs): 1HR 8M – 23% within < 15m – 38% within < 30m – 61% within < 1hr – 83% within < 2hr – 92% within < 3hr

FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com