V I V O Stand-v003v Triple Vertical Monitor Desk Mount Instruction Manual

STAND-V003V Triple Vertical Monitor Desk Mount

Product Information: Triple Vertical Monitor Desk Mount

The Triple Vertical Monitor Desk Mount is a sturdy and durable
mount designed to hold three monitors vertically. It comes with an
instruction manual and all the necessary hardware for installation.
The mount is compatible with flat and curved monitors and can hold
up to 22 lbs (10 kg) per arm. It is important to note that
exceeding the weight capacity may result in serious injury.

The package contents include a pole set, clamp, clamp brace,
monitor bracket, VESA plate, M4x6 bolt, M10 washer, spring washer,
grommet base plate, wire clip, Allen key set, M4x12 thumbscrew,
M4x30 screw, M4 spacer, and soft pads. Some of the hardware
included may not be used.

The mount can be installed using either a desk clamp or grommet
base, depending on the thickness of the desktop. The monitor
bracket can be adjusted for tilting angle using the grub screw.

Product Usage Instructions

Tools Needed

• Phillips Screwdriver
• Drill
• Allen Key Set (included)

Assembly Steps

Pre-Assembly

Thread the Pole Set (A) together as shown in the instruction
manual.

Option A: Desk Clamp Install

1. Install the clamp brace (C) to the pole (A) using x3 M5x14
   bolts (F).
2. Attach soft pad (Q1) to the clamp brace (C).
3. Install the clamp (B) to the pole assembly according to the
   thickness of the desktop. Use x2 M8x12 bolts (G) to connect and
   tighten using the Allen key (M). Tighten the clamp to the desktop
   using the plastic knob.

Option B: Grommet Install

1. If the desk does not have an existing grommet, drill a hole
   using a drill bit (not included).
2. Place the grommet base plate (K) over the hole and secure with
   x1 M10 washer (I) and x1 spring washer (J).
3. Thread the pole set (A) through the grommet base plate
   (K).

Install Monitor Bracket and VESA Plate

1. Attach the monitor bracket (D) to the pole (A) using the
   supplied Allen key (M). Attach the wire clip (L) to the pole
   (A).
2. For flat back monitors, install the VESA plate (E) to the
   monitor using x4 M4x12 thumbscrews (N). For curved back monitors,
   use x4 M4x30 screws (O) and x4 M4 spacers (P).
3. Slide the monitor onto the head of the monitor bracket (D) and
   install the M4x6 bolt (H). Make sure the bolt is installed before
   rotating the monitor.

Tilting Angle Adjustment

Fasten the grub screw in the monitor bracket to fix the tilting
angle using the provided Allen key (M). Manage the wires as shown
in the instruction manual.

If any parts are received damaged or defective, please contact
VIVO support for immediate assistance with rapid response
times.

Triple Vertical Monitor Desk Mount
Instruction Manual

SKU: STAND-V003V
Scan the QR code with your mobile device or follow the link for helpful videos and specifications related to this product. https://vivo-us.com/products/stand-v003v
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

[email protected]

www.vivo-us.com Chat live with an agent!

309-278-5303

WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER: · NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND. · USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
PACKAGE CONTENTS

A (x1) Pole Set
F (x3) M5x14

B (x1) Clamp
G (x2) M8x12

C (x1) Clamp Brace

D (x3) Monitor Bracket

E (x3) VESA Plate

H (x3) M4x6

I (x1) M10 Washer

J (x1) Spring Washer

K (x1) Grommet Base
Plate

L (x3) Wire Clip

M (x1) Allen Key set

N (x12) M4x12 Thumbscrew

O (x12) M4x30

P (x12) M4 Spacer

Q1 (x1) Soft Pad

Q2 (x1) Soft Pad
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED

2

TOOLS NEEDED

Phillips

Drill

Screwdriver

DO NOT EXCEED WEIGHT CAPACITY.
22 lbs

Failure to do so may result in serious injury.

(10 kg)

PER ARM

ASSEMBLY STEPS
PRE-ASSEMBLY
Thread the Pole Set (A) together as shown below.

STEP 1
Option A: Desk Clamp Install
1. Install the clamp brace (C) to the pole (A) using x3 M5x14 bolts (F). See Figure 1. 2. Attach soft pad (Q1) to the clamp brace (C) , see Figure 2. 3. Install the clamp (B) to the pole assembly according to the thickness of the desktop. The
thickness can be changed to 3 positions. Connect using x2 M8x12 bolts (G) and tighten using the Allen key (M). Tighten the clamp to the desktop using the plastic knob. See Figure 3.

aA
G

C

F

M

Q1

B

Figure 1

Figure 2

3

STEP 1 (Continued)
Option B: Grommet Install 1. If desk does not have an existing grommet
hole, drill a 3/8″ (10mm) diameter hole at the desired position through the mounting surface. 2. Completely disassemble clamp (B) into individual parts. Set knob (B1) and clamp plate (B2) aside for later use. The L bracket, bolt, washer and bushing will not be used. 3. Install grommet base plate (K) to the pole (A) using x3 M5x14 bolts (F). See Figure 4. 4. Attach soft pad (Q2) to the grommet base plate (K), see Figure 5. 5. Position pole (A) on the mounting surface and secure using the clamp plate (B2), spring washer (J), M10 washer (I) and knob (B1). See Figure 6.

B2

aA

Km

fF

B1

Figure 4

Qt22

Figure 5

B2

J

B1

I

STEP 2

Install Monitor Bracket (D) to the Pole (A). Fasten the bolt with supplied Allen Key (M). Attach the

Wire Clip (L) to the pole (A).

D

A

M L

STEP 3
OPTION A: Flat Back Monitor For flat back monitor, install VESA Plate (E) to monitor using thumbscrews (N). NOTE: Hand tighten screws to avoid over tightening.
OPTION B: Curved Back Monitor For curved back monitor, install VESA Plate (E) to monitor using bolts (O) and spacers (P). NOTE: Gently tighten using a screwdriver

E N
PE O

4

5

STEP 4
Slide the monitor onto the head of Monitor Bracket (D) as shown in the above diagram.
D Install the M4x6 Bolt (H). Make sure the bolt is installed before you rotate the monitor.

STEP 5
Fasten the grub screw in Monitor Bracket to fix the tilting angle by provided Allen Key (M). Manage the wires as shown in the diagram below.
M
grub scre w

H

6

7

Love your new VIVO setup and want to share? Tag us in your photo! @vivo_us

LAST UPDATED: 10/24/2022 REV1

Open Monday – Friday 7:00am – 7:00pm CST, our dedicated support team can offer immediate assistance with rapid response times. If any parts are received damaged or defective, please contact us. We are happy to replace parts to ensure you have a fully functioning product.

www.vivo-us.com
Chat live with an agent!

AVG. RESOLUTION TIME (within office hrs): < 15 M

309-278-5303

AVG. RESOLUTION TIME (within office hrs): 5M 4S

[email protected]

AVG. RESPONSE TIME (within office hrs): 1HR 8M – 23% within < 15m – 38% within < 30m – 61% within < 1hr – 83% within < 2hr – 92% within < 3hr

FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com

References

• Register a .US.COM domain today!
• VIVO - Desks, Monitor Mounting, and More Home & Office Solutions – VIVO - desk solutions, screen mounting, and more
• Triple Vertical Monitor Desk Mount – VIVO - desk solutions, screen mounting, and more