P2264-084-L Double Take 150-Watt Equivalence Integrated LED Brushed Nickel Pendant
Product Information
The P2264-084-L is a light fixture that can be mounted on a wall
or ceiling. It comes with a mounting plate, ground screw, and two
mounting screws. The fixture has fixture wires for black/smooth,
white/ribbed, and bare copper (ground). The house wires are black
(hot), white (neutral), and green (ground). The fixture is dimmable
with ELV and/or LED compatible wall dimmer switch.
Product Usage Instructions
- Before beginning installation, shut off power at the fuse or
circuit breaker. - Attach the mounting plate (C) to the junction box (A) using the
two mounting screws (E) provided. - If there is a ground wire in the junction box, connect the
fixture’s ground wire to it. Otherwise, connect the fixture’s
ground wire directly to the mounting plate using the green screw
provided. - Connect the fixture wires to the house wires as follows:
- Black/smooth fixture wire to black (hot) house wire
- White/ribbed fixture wire to white (neutral) house wire
- Bare copper (ground) fixture wire to green (ground) house
wire
- Once all wires are connected, tuck them carefully into the
junction box. - Align the canopy (J) to the mounting plate (C) and secure with
screws (G). - Turn on power to the junction box and test the fixture.
Important note: The fixture should be installed by a qualified
electrician to ensure proper wiring and installation. Also, do not
apply pressure to the LEDs when handling the fixture. Hold the
fixture by the base or fixture body only.
INSTALLATION INSTRUCTIONS
For P2264-084-L
W ARNI NG ! S HUT POWER O FF AT FUSE OR CIRCUI T BRE AKE R.
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
MOUNTING THE FIXTURE (Fig. 1) 1. Shut off power at the fuse box or circuit breaker box. If necessary remove the existing fixture and its mounting hardware. 2. Carefully remove the new fixture from the carton and check that all parts are included as shown in the illustration. 3. Rotate rings (R) and (Q) to the desired positions. 4. Attach mounting plate (C) to junction box (A) (not included) using mounting screws (E) (Size: #8-32*1/2″L). The side of the mounting plate marked “GND” must face out. 5. Determine the desired hanging height and thread rods (K2 and K1) to all thread on top of fixture body (M). Attach canopy (J) by screwing onto rod (K1). Carefully pass the wires through each rod during assembly. Note: Remove all thread if installing with one 6″ rod only. 6. There are two drivers inside the canopy, connect driver output wire to LED wire with wire nuts (F) as below: -Red driver output wire (labeled 350mA Output+) to red LED wire (labeled 350mA LED+) -Black driver output wire (labeled 350mA Output-) to black LED wire (labeled 350mA LED-) -Red driver output wire (labeled 450mA Output+) to red LED wire (labeled 450mA LED+) -Black driver output wire (labeled 450mA Output-) to black LED wire (labeled 450mA LED-)
Fig. 1
A-021-125D for P2264-084-L
-Mounting plate (C) -Ground screw (N) -Mounting screw*2 (E)
CONNECTION THE WIRES (Fig. 2) 7. Connect the electrical wires as shown in Fig. 2, making sure that all wire connectors are secured. If your junction box (A) has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting plate (C) using the green screw provided. After the wires are connected, tuck them carefully into the junction box (A).
FINISHING THE INSTALLATION (Fig. 1) 8. Align canopy (J) to mounting plate (C) and secure with screws (G).
Fig. 2
FIXTURE WIRES Black or Smooth
FIXTURE WIRES White or Ribbed
FIXTURE WIRES Bare Copper (Ground)
Your installation is now complete. Return power to the junction box and test the fixture.
CAUTION / ATTENTION: When handling the fixture, do not apply pressure to the LEDs. Hold the fixture by the base or fixture body only.
HOUSE WIRES Black (Hot)
HOUSE WIRES White (Neutral)
HOUSE WIRES Green (Ground)
IMPORTANT: Fixture should be installed by a qualified electrician to ensure proper wiring and installation.
Dimmable with ELV and/or LED compatible wall dimmer switch.
