P1910-66A-L Modern Ceiling Light Pendant
Product Information
The product is an LED fixture with a model number of
P1910-84/66A-L. It comes with installation instructions and was
manufactured on June 25th, 2021. The fixture can be dimmed using
LED compatible wall dimmer switches. The installation process
involves shutting off power, removing screws, and replacing the LED
driver without cutting wires or damaging any decorative elements
attached to the fixture. The fixture has black or smooth wires for
fixture connection, white or ribbed wires for house connection, and
green or bare copper wires for ground connection.
Product Usage Instructions
Before installing or replacing the LED driver, make sure to shut
off power at the fuse box or circuit breaker box. Follow the steps
below for installation:
- Shut off power at the fuse box or circuit breaker box.
- Remove lock screws (F) on the canopy (E) from mounting plate
(C) with a screwdriver (not included). - Loosen screws (CC) and carefully remove the LED driver (BB)
from the ceiling canopy (E). - Un-twist wire nuts (DD) to loosen red and yellow wires.
- Install the new LED driver by reversing steps a to d.
- Once installed, return power to the outlet box and test the
fixture.
Note that the illustration in Fig.1 of the manual is for
installation purposes only and may not be identical to the fixture
purchased. Additionally, connect black or smooth wires of the
fixture to the black (hot) wires of the house, white or ribbed
wires of the fixture to white (neutral) wires of the house, and
green or bare copper wires of the fixture to green (ground) wires
of the house.
INSTALLATION INSTRUCTIONS
Item#P1910-84/66A-L (New. 2021/6/25) READ AND SAVE THESE INSTRUCTIONS
W AR NI NG ! SH UT P O WE R O FF AT F US E O R CI RC UIT BRE AKE R.
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
PREPARATION (Fig.1) 1. Shut off power at the fuse box or circuit breaker box
and remove the old fixture including the mounting hardware. 2. Carefully unpack your new fixture and lay out all the parts in a clean area. Take care not to misplace any small parts necessary for installation. 3. Remove mounting plate (C) from ceiling canopy (E). Secure mounting plate (C) to outlet box (A) (Not included) with the mounting screws (D). Tighten until snug. Make sure the side of mounting plate (C) marked “GND” must face out. 4. Press the wire restraint (G) on ceiling canopy (E) to adjust cable to desired height by pulling and pushing the cable. WIRES CONNECTIONS (Fig.2) 5. Pull power supply wires out from outlet box (A). Connect black supply wire to black fixture wire using wire nuts (B). Connect white supply wire to white fixture wire using wire nuts (B). Connect fixture ground wire and supply ground wire together using wire nuts (B). If your outlet box does not have a ground wire, connect the fixture’s ground wire directly to the mounting plate (A) using the green screw provided. Secure all wire nuts with electrical tape. COMPLETING THE INSTALLATION (Fig.1) 6. Assembling fixture body to outlet box (A). Line up holes on ceiling canopy (E) and mounting holes on mounting plate (C). Secure with lock screws (F). Tighten until snug. Replacing LED driver (Fig. 3)
The LED driver can be replaced by a qualified electrician without cutting of wire and without damage to any decorative element to which the fixture is attached. See installation steps for more details (Fig.3)
a. Shut off the power. b. Remove lock screws (F) on canopy (E) from mounting
plate (C) with screw driver (Not included). (Fig.1) c. Loosen screws (CC) and carefully remove led driver
(BB) from ceiling canopy (E). d. Un-twist wire nuts (DD) to loosen red and yellow
wires. e. Reverse steps a-d for installing new LED driver
Your installation is now complete. Return power to
outlet box and test the fixture.
Fig. 1
Fig. 2
FIXTURE WIRES Black or Smooth
Fig. 3
FIXTURE WIRES White or Ribbed HOUSE WIRES Black (Hot)
Set#A-016 -Mounting Plate -Ground Screw -Mounting Screw*2
FIXTURE WIRES Green or Bare Copper (Ground) HOUSE WIRES White (Neutral)
HOUSE WIRES Green (Ground)
Note: Illustration (Fig.1) on this manual is for installation purposes only. It may or may not be
identical to the fixture purchased. Dimmable with LED compatible wall dimmer switches.
LA-3188E
