P1911-084 Recovery Integrated LED Circular Pendant
Product Information: LED Driver Replacement Kit
The LED Driver Replacement Kit, item number P1911-084/66A-L, is
a kit that allows you to replace the LED driver of your lighting
fixture without cutting wires or damaging any decorative elements.
This kit is designed to work with dimmable ELV and/or LED
compatible wall dimmer switches. The product comes with a mounting
plate, ground screw, and two mounting screws. The kit is designed
to work with fixtures that have black or smooth, white or ribbed,
and green or bare copper fixture wires and black (hot), white
(neutral), and green (ground) house wires. The installation
instructions for this product are provided below.
Product Usage Instructions:
- Before starting the installation process, shut off power at the
fuse box or circuit breaker box. This is essential for your
safety. - Remove the lock screws (F) on the canopy (E) from the mounting
plate (C) using a screwdriver (not included). Disconnect the
fixture wires from the outlet box (A). - Loosen screws (CC) and carefully remove the LED driver (BB)
from the ceiling canopy (E). - Un-twist wire nuts (DD) to loosen red and yellow wires.
- Install the new LED driver by reversing steps 1-4.
- Once the new LED driver is installed, return power to the
outlet box and test the fixture.
Note: The illustration provided in Fig. 1 is for installation
purposes only and may or may not be identical to the fixture
purchased.
INSTALLATION INSTRUCTIONS
Item#P1911-084/66A-L (New.2022/04/13) READ AND SAVE THESE INSTRUCTIONS
W A R N I N G ! S H U T P O W E R O F F AT F U S E O R C I R C U I T B R E A K E R .
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
PREPARATION (Fig.1) 1. Shut off power at the fuse box or circuit breaker box
and remove the old fixture including the mounting hardware. 2. Carefully unpack your new fixture and lay out all the parts in a clean area. Take care not to misplace any small parts necessary for installation. 3. Remove mounting plate (C) from ceiling canopy (E). Secure mounting plate (C) to outlet box (A) (Not included) with the mounting screws (D). Tighten until snug. Make sure the side of mounting plate (C) marked “GND” must face out. 4. Press the wire restraint (G) on ceiling canopy (E) to adjust cable to desired height by pulling and pushing the cable. WIRES CONNECTIONS (Fig.2) 5. Pull power supply wires out from outlet box (A). Connect black supply wire to black fixture wire using wire nuts (B). Connect white supply wire to white fixture wire using wire nuts (B). Connect fixture ground wire and supply ground wire together using wire nuts (B). If your outlet box does not have a ground wire, connect the fixture’s ground wire directly to the mounting plate (C) using the green screw provided. Secure all wire nuts with electrical tape. COMPLETING THE INSTALLATION (Fig.1) 6. Assembling fixture body to outlet box (A). Line up holes on ceiling canopy (E) and mounting holes on mounting plate (C). Secure with lock screws (F). Tighten until snug. Replacing LED driver (Fig. 3)
The LED driver can be replaced by a qualified electrician without cutting of wire and without damage to any decorative element to which the fixture is attached. See installation steps
for more details (Fig.3)
a. Shut off the power. b. Remove lock screws (F) on canopy (E) from mounting
plate (C) with screw driver (Not included). Disconnect the
fixture wires from the outlet box (A). (Fig.1) c. Loosen screws (CC) and carefully remove led driver
(BB) from ceiling canopy (E). d. Un-twist wire nuts (DD) to loosen red and yellow
wires. e. Reverse steps a-d for installing new LED driver Your installation is now complete. Return power to
outlet box and test the fixture.
Fig. 1
Fig. 2
FIXTURE WIRES Black or Smooth
Fig. 3
FIXTURE WIRES White or Ribbed HOUSE WIRES Black (Hot)
Set#A-020-145 -Mounting Plate -Ground Screw -Mounting Screw*2
FIXTURE WIRES Green or Bare Copper (Ground) HOUSE WIRES White (Neutral)
HOUSE WIRES Green (Ground)
Note: Illustration (Fig.1) on this manual is for installation purposes only. It may or may not be identical to the fixture purchased. Dimmable with ELV and/or LED compatible wall dimmer switches.
LA-3188E
