P1912-66A-L Recovery Integrated LED Circular Pendant
Product Information
The product being discussed is Item #P1912-084/66A-L. It is an
LED driver that can be replaced by a qualified electrician without
cutting any wires or damaging any decorative elements of the
fixture to which it is attached. The fixture is dimmable with ELV
and/or LED compatible wall dimmer switches. The installation manual
is identified as LA-3188E.
Product Usage Instructions
- Shut off power at the fuse box or circuit breaker box.
- Remove lock screws (F) on canopy (E) from mounting plate (C)
with screwdriver (not included). Disconnect the fixture wires from
the outlet box (A). - Loosen screws (CC) and carefully remove LED driver (BB) from
ceiling canopy (E). - Un-twist wire nuts (DD) to loosen red and yellow wires.
- Reverse steps a-d for installing new LED driver. Ensure that
the black or smooth fixture wires are connected to the black or hot
house wires, the white or ribbed fixture wires are connected to the
white or neutral house wires, and the green or bare copper fixture
wire is connected to the green or ground house wire. - Return power to outlet box and test the fixture.
Note: The illustration in Fig.1 of the manual is for
installation purposes only and may not be identical to the fixture
purchased.
INSTALLATION INSTRUCTIONS
Item#P1912-084/66A-L (New.2022/04/13) READ AND SAVE THESE INSTRUCTIONS
W A R N I N G ! S H U T P O W E R O F F AT F U S E O R C I R C U I T B R E A K E R .
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
PREPARATION (Fig.1) 1. Shut off power at the fuse box or circuit breaker box
and remove the old fixture including the mounting hardware. 2. Carefully unpack your new fixture and lay out all the parts in a clean area. Take care not to misplace any small parts necessary for installation. 3. Remove mounting plate (C) from ceiling canopy (E). Secure mounting plate (C) to outlet box (A) (Not included) with the mounting screws (D). Tighten until snug. Make sure the side of mounting plate (C) marked “GND” must face out. 4. Press the wire restraint (G) on ceiling canopy (E) to adjust cable to desired height by pulling and pushing the cable. WIRES CONNECTIONS (Fig.2) 5. Pull power supply wires out from outlet box (A). Connect black supply wire to black fixture wire using wire nuts (B). Connect white supply wire to white fixture wire using wire nuts (B). Connect fixture ground wire and supply ground wire together using wire nuts (B). If your outlet box does not have a ground wire, connect the fixture’s ground wire directly to the mounting plate (C) using the green screw provided. Secure all wire nuts with electrical tape. COMPLETING THE INSTALLATION (Fig.1) 6. Assembling fixture body to outlet box (A). Line up holes on ceiling canopy (E) and mounting holes on mounting plate (C). Secure with lock screws (F). Tighten until snug. Replacing LED driver (Fig. 3)
The LED driver can be replaced by a qualified electrician without cutting of wire and without damage to any decorative element to which the fixture is attached. See installation steps
for more details (Fig.3)
a. Shut off the power. b. Remove lock screws (F) on canopy (E) from mounting
plate (C) with screw driver (Not included). Disconnect the
fixture wires from the outlet box (A). (Fig.1) c. Loosen screws (CC) and carefully remove led driver
(BB) from ceiling canopy (E). d. Un-twist wire nuts (DD) to loosen red and yellow
wires. e. Reverse steps a-d for installing new LED driver Your installation is now complete. Return power to
outlet box and test the fixture.
Fig. 1
Fig. 2
FIXTURE WIRES Black or Smooth
Fig. 3
FIXTURE WIRES White or Ribbed HOUSE WIRES Black (Hot)
Set#A-020-145 -Mounting Plate -Ground Screw -Mounting Screw*2
WFIIXRTEUSRE Green or Bare Copper (Ground)
HOUSE WIRES White (Neutral)
HOUSE WIRES Green (Ground)
Note: Illustration (Fig.1) on this manual is for installation purposes only. It may or may not be identical to the fixture purchased. Dimmable with ELV and/or LED compatible wall dimmer switches.
LA-3188E
