P1301-L LED Pendant Light
Product Information
The P1301-L is an LED pendant light fixture that requires
installation by a qualified electrician. The fixture is dimmable
with ELV and/or LED compatible wall dimmer switches. The package
includes a mounting plate, canopy, hanger ball, screws, rods, and a
glass finial. The LED module should be provided by a specified
supplier.
Product Usage Instructions
- Read and save the installation instructions.
- Shut off power at the fuse or circuit breaker before
installation. - Connect the wires as shown in Figure 3, making sure all wire
connectors are secured. If your outlet has a ground wire (green or
bare copper), connect the ground wire from the hanger ball and
mounting plate to it. Otherwise, connect the ground wire from the
hanger ball directly to the mounting plate ground wire and secure
with wire connectors provided. After the wires are connected, tuck
them carefully into the ceiling junction box. - Align the canopy over the mounting plate and secure with
screws. - Align the glass to the fixture body and secure with the
finial. - To replace the LED module, follow these steps:
- Remove the glass and gasket by loosening screws (Q) and (J)
respectively. - Remove spacers (O), gasket (M1), and LED module (L) from pan
(K). - Disconnect the wire using a screwdriver from wire connector
(S). - Reverse steps a-c for installing the new LED module.
- Remove the glass and gasket by loosening screws (Q) and (J)
Note: The fixture should be installed by a qualified electrician
to ensure proper wiring and installation.
INSTALLATION INSTRUCTIONS FOR P1301-L For LED Pendant
READ AND SAVE THESE INSTRUCTIONS
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER
AV ER TI SSEME NT !CO UPER L E C OUR ANT AU NIVE AU DE S FUSIBL ES O U DO DI SJO NCT EU
ASSEMBLING THE FIXTURE (Fig.1 Fig.2) 1 Shut off power at the fuse box or circuit breaker. If necessary, remove the old fixture including the mounting hardware. 2 Carefully remove the fixture from the carton and check that all parts are included as show in Figure 1. 3 Loosen screws (D) and remove mounting plate (A) from canopy (C). Attach mounting plate (A) (Part# LTG BKT10) to the junction box using mounting screws (B) (size:8-32*1/2″L). 4 This fixture includes three 12″ and one 6″ rod. Determine the desired hanging height and thread rods F1 (Part#W30-1-655), F2 (Part#W301-655), F3 (Part#W30-H-655) to fixture (G). Pass the wires carefully through each rod during assembly. Next place canopy (C) over rods (F) and thread hanger ball (E) to rod (F). Please remove the nipple if installing with one 6″ rod only. 5 While holding the fixture body, install the fixture into the mounting plate (A) by tilting at a slight angle so that the hanger ball (E) slips into the mounting plate (A) as shown. Align the notch in the hanger ball (E) to the tab on the mounting plate (A) to prevent the fixture from turning.
CONNECTING THE WIRES (Fig. 3) 6 At this point, connect the electrical wire as shown in figure 3, making sure that all wire connectors are secured. If your outlet has a ground wire (green or bare copper), connect the ground wire from the hanger ball and mounting plate to it. Otherwise, connect the ground wire from hanger ball directly to the mounting plate ground wire and secure with wire connectors provided. After the wires are connected, tuck them carefully into the ceiling junction box.
FINISHING THE INSTALLATION (Fig.1) 7 Align canopy (C) over mounting plate (A) and secure with screws (D). 8 Align glass (H) to the fixture body and secure with finial (I).
Your installation is now complete. Return power to the junction box and test the fixture. CAUTION/ATTENTION: When handling the fixture, do not apply pressure to the LEDs. Hold the fixture by the base (G) only. Replacing LED module (Fig. 4) The LED module can be replaced by a qualified electrician without cutting of wire and without damage to any decorative element to which the fixture is attached. Warning: Turn off power at the circuit breaker before replacing LED module. a. Loosen finial (I) remove glass (H) and loosen screws (R) remove frame
(G) b. Loosen screws (Q) and remove gasket (M2), glass (P). c. Loosen screws (J), (N) and remove spacers (O), gasket (M1). Carefully
remove LED module (L) from pan (K) and disconnect the wire using screwdriver from wire connector (S). d. Reverse steps a-c for installing the new LED module. Note: The LED module should be provided by a specified supplier.
IMPORTANT: Fixture should be installed by a qualified electrician to ensure proper wiring and installation. Dimmable with ELV and/or LED compatible wall dimmer switches.
Fig.3
Fig.1 Fig.4
Page 1/2
Fig.2
a. Hardware Bag: A. Mounting plate x 1 C. Canopy x 1 D. Screw x 2 E. Hanger ball x 1
b. Hardware Bag: F1. ROD 12″ x 1 F2. ROD 12″ x 2 F3. ROD 6″ x 1
Page 2/2
F2
F3
F1
