Jonathan Y Jyl7599a 63 Inch Wide Led Pendant Light Instruction Manual

JYL7599A 63 Inch Wide LED Pendant Light

Product Information

The JYL7599A is a lighting fixture that requires installation by
a licensed electrician. The product dimensions are 57L X 30W X
(14.5-44.5)H. The package includes a mounting plate, canopy,
screwed balls, ground screw, wire connector, tube, body, and
bulbs.

Part List and Hardware List

The product comes with a warning that if the item is damaged or
has an obvious defect, it should not be installed. The item cannot
be returned once it has been installed.

Product Usage Instructions

Before beginning assembly, ensure that all parts are present and
compare them with the package contents list and hardware contents
list. If any part is missing or damaged, do not attempt to assemble
the product. Estimated assembly time is 20 minutes.

1. Thread mounting screws (A) into the matching holes of the
   mounting plate (B), then fix the mounting plate (B) to the outlet
   box with machine screw (C).
2. Loosen the hex nut of the canopy (F), separate swivel from
   canopy (F).
3. Connect the tubes (H) together to get the desired length and
   fix the bottom end to the nipple of the body (I) and the top end to
   the swivel of the canopy (F).
4. Place the swivel onto the canopy (F), then secure it with the
   hex nut.
5. Make wire connections with wire connectors (E), following the
   reference chart provided in the user manual.
6. Orient the ceiling canopy (F) so that the mounting screws (A)
   protruding from the mounting plate (B) go into the holes in the
   canopy (F), then secure it with the provided screwed balls
   (G).
7. Install bulb (J). Be sure to use a light bulb(s) with wattage
   no greater than specified on this fixture. Always make sure that
   electrical current is turned off before changing bulbs.

The user manual specifies that only on/off type A bulb max
40-watt or LED bulb max 9-watt should be used. There are LED 8pcs
4watt bulbs included in the box.

WARNING WE RECOMMEND INSTALLATION OF THIS LIGHTING FIXTURE BE DONE BY A LICENSED ELECTRICIAN. WARNING *** SWITCH OFF THE MAIN ELECTRICAL SUPPLY FROM THE MAIN FUSE BOX/CIRCUIT BREAKER BEFORE INSTALLATION. INSPECT ITEM CAREFULLY BEFORE ATTEMPTING TO INSTALL. IF THERE IS ANY DAMAGE OR OBVIOUS DEFECT, DO NOT INSTALL. ITEM MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALLED.
CARE AND MAINTENANCE To clean the outside of the fixture, use a dry or slightly dampened clean cloth (use clean water, never a solvent) to wipe the surface of the fixture. To clean the inside of the fixture, first disconnect power to the fixture by turning off the circuit breaker or by removing the fuse at the fuse box. Next, use a dry or slightly dampened clean cloth (use clean water, never a solvent) to wipe the interior surface of the fixture. Do not use any cleaners with chemical, solvents or harsh abrasives. Use only a dry soft cloth to dust or wipe carefully.
NOTICE& IMPORTANT SAFETY INSTRUCTIONS * Please make sure that you have all parts indicated before you begin assembly of this item * This item should be assembled on a soft surface to prevent scratching the finish during assembly * To reduce the risk of fire, electrical shock or injury to persons or property, please follow the guideline below for safe use and installation *The external flexible cable or cord of this luminaire cannot be replaced If the cord is damaged, the luminaire shall be destroyed
Part List and Hardware List
PIECE DESCRIPTION PICTURE QUANTITY PIECE DESCRIPTION PICTURE QUANTITY

A

mounting screw

2X

F

canopy

1X

B mounting plate

1X

G

screwed ball

2X

C machine screw

2X

H

tube

12″ – 4X 6″ – 4X

D ground screw

1X

I

body

1X

E wire connector

3X

J

bulb

8X

Model#: JYL7599A Product Dimensions: 57″L X 30″W X (14.5-44.5″)H

1/2

PREPARATION

Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product. Estimated Assembly Time: 20 minutes.
1. Thread mounting screws (A) into the mattch holes of the mounting plate(B), then fix the mounting plate(B) to the outlet box with machine screw(C).
2. Loosen the hex nut of the canopy (F) ,separate swivel from canopy(F).
3. connect the tubes(H) together to get desired length and fix the bottom end to nipple of the body (I), the top end to the swivel of the canopy (F).
4. Place the swivel onto the canopy (F),then secure with the hex nut.
5. Make wire connections, with wire connectors(E), following the reference chart listed below.

Connect, Hot, Black or Red Outlet Supply Wire to:

Black * Parallel Cord (round & smooth)
Clear, Brown, Gold or Black without Tracer stripes)

(colored

Connect, Neutral, White Outlet Supply Wire to: White
* Parallel Cord (square & ridged)
Clear, Brown, Gold or Black with Tracer (colored stripes)

Insulated Wire (not green) with copper metal conductor

Insulated Wire (not green) with Silver metal conductor.

*Note: When parallel wire ( SPT I & SPT II ) is used. The neutral wire is square shaped and ridged and the hot wire will be round in shape and smooth. ( See Illustration on left. )

Grounding Instructions: a) For installation in the United States: Wrap ground wire from outlet box around green ground screw(D) on mounting plate, no less than 2″ from wire end. Tighten ground screw. If fixture is supplied with a ground wire, connect to outlet ground wire with a wire connector. b) For installation in Canada: If fixture is supplied with ground wire, wrap ground wire around green grounding screw on mounting plate. Tighten ground screw.
6. Orient the ceiling canopy(F) so that the mounting screws(A) protruding from the mounting plate (B) go into the holes in the canopy (F), then secure it with the provided screwed balls(G).
7. Install bulb(J). Be sure to use light bulb(s) with wattage no greater than specified on this fixture. Always make sure that electrical current is turned off before changing bulbs.

PLEASE USE ON/OFF TYPE”A” BULB MAX 40-WATT OR LED BULB MAX 9 -WATT THERE ARE LED 8PCS 4WATT BULB IN THE BOX
ENJOY YOUR LAMP

2/2