JYL1119A Levi 40.5 Inch Pendant Light
Product Information
The JYL1119A model is a lighting fixture that requires
installation by a licensed electrician. It comes with a mounting
bracket, ground screw, outlet box screw, wire nut, 12 and 6 rods,
fixture body, light bulbs, canopy unit, thread shade, and canopy
nut. The dimensions of the product are 41Lx10.3W x25.5-55.4H. The
lamp requires a Type A bulb with a maximum wattage of 40W or a CFL
bulb with a maximum wattage of 13W or an LED bulb with a maximum
wattage of 9W.
Product Usage Instructions
- Before starting assembly, ensure that all parts are present and
undamaged. - Switch off the main electrical supply from the main fuse
box/circuit breaker before installation. - Inspect the item carefully before installation. Do not install
if there is any damage or obvious defect. - Attach the mounting bracket (A) to the junction box with outlet
box screw (C). - Raise the 12 rod (G) and 6 rod (F) thread to the fixture body
(H), attach the swivel (E1) to the rod (F), then connect
wires. - Connect the hot black or red outlet supply wire to the black
parallel cord (round and smooth). Connect the neutral white outlet
supply wire to the white parallel cord (square and ridged). - Wrap the ground wire from the outlet box around the green
ground screw (B) on the mounting bracket and tighten the ground
screw. If the fixture is supplied with a ground wire, connect it to
the outlet ground wire with a wire nut. - Raise the canopy unit (E) thread to the outlet box screws and
secure it with the canopy nut (K). - Install the light bulb (I) to the socket. Make sure that the
electrical current is turned off before changing bulbs. - Attach the thread shade (J) to the fixture body (H).
- Enjoy your lamp.
Note that the external flexible cable or cord of this lamp
cannot be replaced. If the cord is damaged, the lamp shall be
destroyed. Also, the item may not be returned once it has been
installed.
WARNING WE RECOMMEND INSTALLATION OF THIS LIGHTING FIXTURE BE DONE BY A LICENSED ELECTRICIAN. WARNING *** SWITCH OFF THE MAIN ELECTRICAL SUPPLY FROM THE MAIN FUSE BOX/CIRCUIT BREAKER BEFORE INSTALLATION. INSPECT ITEM CAREFULLY BEFORE ATTEMPTING TO INSTALL. IF THERE IS ANY DAMAGE OR OBVIOUS DEFECT, DO NOT INSTALL. ITEM MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALLED.
CARE AND MAINTENANCE To clean the outside of the fixture, use a dry or slightly dampened clean cloth (use clean water, never a solvent) to wipe the surface of the fixture. To clean the inside of the fixture, first disconnect power to the fixture by turning off the circuit breaker or by removing the fuse at the fuse box. Next, use a dry or slightly dampened clean clorth (use clean water, never a solvent) to wipe the interior surface of the fixture. Do not use any cleaners with chemical, solvents or harsh abrasives. Use only a dry soft cloth to dust or wipe carefully.
Model#: JYL1119A Product Dimensions: 41″Lx10.3″W x25.5″-55.4″H
NOTICE& IMPORTANT SAFETY INSTRUCTIONS * Please make sure that you have all parts indicated before you begin assembly of this item * This item should be assembled on a soft surface to prevent scratching the finish during assembly * To reduce the risk of fire, electrical shock or injury to persons or property, please follow the guideline below for safe use and installation *The external flexible cable or cord of this lamp cannot be replaced If the cord is damaged, the lamp shall be destroyed
Part List and Hardware List
PIECE DESCRIPTION
A
Mounting bracket
B Ground screw
C
Outlet box screw
D
Wire nut
PICTURE QUANTITY PIECE DESCRIPTION
1X
G
12″ rod
1X
H
Fixture body
2X
3X
I
Light bulb
PICTURE
QUANTITY 2X 1X 3X
E Canopy unit
1X
J Thread shade
3X
F
6″ rod
2X
K
Canopy nut
2X
1/2
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product. Estimated Assembly Time: 20 minutes.
1. Attach the mounting bracket (A) to the junction box with outlet box screw (C).
2. Raise the 12″ rod (G) and 6″ rod (F) thread to the fixture body (H), attach the swivel (E1) to the rod
(F), then connect wires.
Connect, Hot, Black or Red Outlet Supply Wire to:
Connect, Neutral, White Outlet Supply Wire to:
Black * Parallel Cord (round & smooth)
White * Parallel Cord (square & ridged)
Clear, Brown, Gold or Black without Tracer (colored stripes)
Clear, Brown, Gold or Black with Tracer (colored stripes)
Insulated Wire (not green) with copper metal conductor
Insulated Wire (not green) with Silver metal conductor.
*Note: When parallel wire ( SPT I & SPT II ) is used. The neutral wire is square shaped and ridged and the hot wire will be round in shape and smooth. ( See Illustration on left. )
Grounding Instructions: a) For installation in the United States: Wrap ground wire from outlet box around green ground screw(B) on mounting bracket, no less than 2″ from wire end. Tighten ground screw. If fixture is supplied with a ground wire, connect to outlet ground wire with a wire nut. b) For installation in Canada: If fixture is supplied with ground wire, wrap ground wire around green grounding screw on mounting bracket. Tighten ground screw.
3. Raise the canopy unit (E) thread to the outlet box screws, secure with canopy nut (K).
4. Install the light bulb (I) to the socket.
5. Attach the thread shade (J) to the fixture body (H).
specified on this fixture. Make sure that electrical current is turned off before changing bulbs.
PLEASE USE TYPE”A” BULB MAX 40-WATT OR CFL BULB MAX 13-WATT OR LED BULB MAX 9-WATT,
I
THERE IS LED 4-WATT BULB IN THE BOX
J
ENJOY YOUR LAMP 2/2
