JYL7553 Kinsley 12 Inch 3-Light Pendant LED
Product Information
This lighting fixture is designed to be installed by a licensed
electrician. It comes with a mounting bracket, machine screw,
chain, fixture loop, lock washer, loop assembly, threaded rod,
ground screw, wire connector, canopy, hang loop, closable link,
canopy nut, glass panel, connecting rod, and bulb. The product
dimensions are 12D X 29-101H.
Product Usage Instructions
- Before beginning assembly, make sure all parts are present and
undamaged. If any part is missing or damaged, do not attempt to
assemble the product. - Thread the center stem (O) onto the socket assembly and swivel
of the loop assembly (M), then thread the fixture loop(L) onto the
nipple of the loop assembly(M). - Connect the chain(K) by fixture loop(L) and hang loop(H) with
the closable link(I). - Secure mounting bracket (A) to outlet box with machine screw
(B), insert lock washer (C), and thread the short threaded rod(D)
onto mounting bar (A), then secure it with the nut of the short
threaded rod(D). - Make wire connections with wire connectors(F), following the
reference chart provided in the instructions. - Orient the ceiling canopy(G) so that the short threaded rod(D)
goes into the holes in the canopy, and thread the hang loop(H) onto
the short threaded rod(D), then secure it with the canopy
nut(J). - Insert the curved glass (S) into the frame (R) and fix it with
small plate of the frame (R) inside. - Hook the connecting rod (N) on the loop assembly(M) and the
frame (R). - Install bulbs(P). Be sure to use light bulb(s) with wattage no
greater than specified on this fixture. Always make sure that
electrical current is turned off before changing bulbs.
Please note that this product cannot be returned once it has
been installed. Also, ensure that you follow the grounding
instructions provided in the manual before installation.
WARNING WE RECOMMEND INSTALLATION OF THIS LIGHTING FIXTURE BE DONE BY A LICENSED ELECTRICIAN. WARNING *** SWITCH OFF THE MAIN ELECTRICAL SUPPLY FROM THE MAIN FUSE BOX/CIRCUIT BREAKER BEFORE INSTALLATION. INSPECT ITEM CAREFULLY BEFORE ATTEMPTING TO INSTALL. IF THERE IS ANY DAMAGE OR OBVIOUS DEFECT, DO NOT INSTALL. ITEM MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALLED.
CARE AND MAINTENANCE To clean the outside of the fixture, use a dry or slightly dampened clean cloth (use clean water, never a solvent) to wipe the surface of the fixture. To clean the inside of the fixture, first disconnect power to the fixture by turning off the circuit breaker or by removing the fuse at the fuse box. Next, use a dry or slightly dampened clean cloth (use clean water, never a solvent) to wipe the interior surface of the fixture. Do not use any cleaners with chemical, solvents or harsh abrasives. Use only a dry soft cloth to dust or wipe carefully. NOTICE& IMPORTANT SAFETY INSTRUCTIONS * Please make sure that you have all parts indicated before you begin assembly of this item * This item should be assembled on a soft surface to prevent scratching the finish during assembly * To reduce the risk of fire, electrical shock or injury to persons or property, please follow the guideline below for safe use and installation *The external flexible cable or cord of this lamp cannot be replaced If the cord is damaged, the lamp shall be destroyed
Part List and Hardware List
PIECE DESCRIPTION
A
mounting bracket
B machine screw
PICTURE
QUANTITY PIECE DESCRIPTION
1X
K
chain
2X
L
Fixture Loop
PICTURE QUANTITY 1X 1X
C
lock washer
1X
M Loop Assembly
1X
short
D
threaded rod
1X
N Connecting Rod
3X
E ground screw
1X
O
Center stem
1X
F wire connector
3X
P
Bulb
3X
G
canopy
1X
Q Socket Assembly
1X
H
hang loop
1X
R
Frame
1X
I
Closable Link
J
Canopy Nut
2X
S
Glass panel
1X
3X 1/2
Model#: JYL7553 Product Dimensions: 12″D X 29-101″H
Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product. Estimated Assembly Time: 20 minutes.
1.Thread the center stem (O) onto the socket assembly and swivel of the loop assembly (M), then thread the fixture fixture loop(L) onto the nipple of the loop assembly(M). .
2.Connect chain(K) by fixture loop(L) and hang loop(H) with the closable link(I).
3.Secure mounting bracket (A) to outlet box with machine screw (B),Insert lock washer (C) and thread the short threaded rod(D) onto mounting bar (A), then secure with the nut of the short threaded rod(D).
4. Make wire connections, with wire connectors(F), following the reference chart listed below.
ack or Red Outlet Supply Wire to:
Black el Cord (round & smooth)
Connect, Neutral, White Outlet Supply Wire to:
White * Parallel Cord (square & ridged)
Clear, Brown, Gold or Black without Tracer (colored stripes)
Clear, Brown, Gold or Black with Tracer (colored stripes)
Insulated Wire (not green) with copper metal conductor
Insulated Wire (not green) with Silver metal conductor.
*Note: When parallel wire ( SPT I & SPT II ) is used. The neutral wire is square shaped and ridged and the hot wire will be round in shape and smooth. ( See Illustration on left. )
Grounding Instructions: a) For installation in the United States: Wrap ground wire from outlet box around green ground screw(E) on mounting bracket, no less than 2″ from wire end. Tighten ground screw. If fixture is supplied with a ground wire, connect to outlet ground wire with a wire connector. b) For installation in Canada: If fixture is supplied with ground wire, wrap ground wire around green grounding screw on mounting bracket. Tighten ground screw.
5. Orient the ceiling canopy(G) so that the short threaded rod(D) into the holes in the canopy, and thread the hang loop(H) onto the short threaded rod(D), then secure it with the canopy nut(J).
6. Insert the curved glass (S) to the frame (R), fix it with small plate of the frame (R) inside.
7. Hook the connecting rod (N) on the loop assembly(M) and the frame (R).
8. Install bulbs(P). Be sure to use light bulb(s) with wattage no greater than specified on this fixture. Always make sure that electrical current is turned off before changing bulbs.
PLEASE USE ON/OFF TYPE”B” BULB MAX 40-WATT OR LED BULB MAX 9-WATT. THERE ARE 3PCS LED 4-WATT BULBS IN THE BOX
ENJOY YOUR LAMP
2/2
