JYL7586A LED Pendant Lamp
Product Information:
- Model #: JYL7586A
- Product Dimensions: 12Dx23-95H
- Estimated Assembly Time: 20 minutes
- Maximum Bulb Wattage: Type A Bulb – 60W, CFL Bulb – 13W, LED
Bulb – 9W
Product Usage Instructions:
- WARNING: We recommend installation of this lighting fixture be
done by a licensed electrician. - WARNING: Switch off the main electrical supply from the main
fuse box/circuit breaker before installation. - Inspect the item carefully before attempting to install. If
there is any damage or obvious defect, do not install. The item may
not be returned once it has been installed. - Before beginning assembly of the product, make sure all parts
are present. Compare parts with the package contents list and
hardware contents list. If any part is missing or damaged, do not
attempt to assemble the product. - Attach the mounting bar (A) to the junction box with the outlet
box screw (C). - Connect the fixture body (J) and rod (H) together with the lock
link (I). Attach the metal chain (G) to the canopy unit (F) on the
top and to the rod (H) on the bottom. - Connect wires according to the following instructions:
- Connect Hot, Black or Red Outlet Supply Wire to Black Parallel
Cord (round & smooth). - Connect Neutral, White Outlet Supply Wire to White Parallel
Cord (square & ridged). - Connect Clear, Brown, Gold or Black without Tracer (colored
stripes) to Insulated Wire (not green) with copper metal
conductor. - Connect Clear, Brown, Gold or Black with Tracer (colored
stripes) to Insulated Wire (not green) with Silver metal
conductor. - Note: When parallel wire (SPT I & SPT II) is used, the
neutral wire is square shaped and ridged, and the hot wire will be
round in shape and smooth.
- For installation in the United States: Wrap the ground wire
from the outlet box around the green ground screw (B) on the
mounting bar, no less than 2 inches from the wire end. Tighten the
ground screw. If the fixture is supplied with a ground wire,
connect it to the outlet ground wire with a wire nut. - For installation in Canada: If the fixture is supplied with a
ground wire, wrap the ground wire around the green grounding screw
on the mounting bar. Tighten the ground screw.
screws. Secure it with the canopy nut (E).
Bulb max 60W or CFL Bulb max 13W or LED Bulb max 9W. There is 1PC
LED 4W Bulb in the box.
WARNING WE RECOMMEND INSTALLATION OF THIS LIGHTING FIXTURE BE DONE BY A LICENSED ELECTRICIAN. WARNING *** SWITCH OFF THE MAIN ELECTRICAL SUPPLY FROM THE MAIN FUSE BOX/CIRCUIT BREAKER BEFORE INSTALLATION. INSPECT ITEM CAREFULLY BEFORE ATTEMPTING TO INSTALL. IF THERE IS ANY DAMAGE OR OBVIOUS DEFECT, DO NOT INSTALL. ITEM MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALLED.
CARE AND MAINTENANCE To clean the outside of the fixture, use a dry or slightly dampened clean cloth (use clean water, never a solvent) to wipe the surface of the fixture. To clean the inside of the fixture, first disconnect power to the fixture by turning off the circuit breaker or by removing the fuse at the fuse box. Next, use a dry or slightly dampened clean cloth (use clean water, never a solvent) to wipe the interior surface of the fixture. Do not use any cleaners with chemical, solvents or harsh abrasives. Use only a dry soft cloth to dust or wipe carefully. NOTICE& IMPORTANT SAFETY INSTRUCTIONS * Please make sure that you have all parts indicated before you begin assembly of this item * This item should be assembled on a soft surface to prevent scratching the finish during assembly * To reduce the risk of fire, electrical shock or injury to persons or property, please follow the guideline below for safe use and installation *The external flexible cable or cord of this lamp cannot be replaced If the cord is damaged, the lamp shall be destroyed
Part List and Hardware List
PIECE DESCRIPTION PICTURE QUANTITY PIECE
PICTURE QUANTITY
A Mounting bar
1X
I
Lock link
1X
B Ground screw
1X
C
Outlet box screw
J
Fixture body
2X
1X
D
Wire nut
3X
K
Light bulb
1X
E Canopy nut
2X
F
Canopy unit
1X
G
Chain
1X
H
Rod
1X
1/2
Model#: JYL7586A Product Dimensions: 12″Dx23″-95″H
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product. Estimated Assembly Time: 20 minutes. 1. Attach the mounting bar (A) to the junction box with outlet box screw (C).
2. Connect the fixture body (J) and rod (H) together with lock link (I), attach the metal chain (G) to the canopy unit (F) on the top and to the rod (H) on the bottom.
3. Connect wires.
Connect, Hot, Black or Red Outlet Supply Wire to:
Black * Parallel Cord (round & smooth)
Connect, Neutral, White Outlet Supply Wire to:
White * Parallel Cord (square & ridged)
Clear, Brown, Gold or Black without Tracer (colored stripes)
Clear, Brown, Gold or Black with Tracer (colored stripes)
Insulated Wire (not green) with copper metal conductor
Insulated Wire (not green) with Silver metal conductor.
*Note: When parallel wire ( SPT I & SPT II ) is used. The neutral wire is square shaped and ridged and the hot wire will be round in shape and smooth. ( See Illustration on left. )
Grounding Instructions: a) For installation in the United States: Wrap ground wire from outlet box around green ground screw(B) on mounting bar, no less than 2″ from wire end. Tighten ground screw. If fixture is supplied with a ground wire, connect to outlet ground wire with a wire nut. b) For installation in Canada: If fixture is supplied with ground wire, wrap ground wire around green grounding screw on mounting bar. Tighten ground screw.
3. Raise the canopy unit (F) thread to the outlet box screws, secure with canopy nut (E). 4. Install the light bulb (K) to the socket.
PLEASE USE TYPE”A” BULB MAX 60-WATT OR CFL BULB MAX 13-WATT OR LED BULB MAX 9-WATT, THERE IS 1PC LED 4-WATT BULB IN THE BOX
ENJOY YOUR LAMP 2/2
