P5481-66A-L Convolution 140-Watt Equivalence Integrated LED Black Island Pendant
Product Information
The P5481/2/3-66A-L is a mountable fixture that can be installed
on a junction box. The fixture comes with a mounting plate set,
which includes a mounting plate, ground screw, and two mounting
screws. The fixture is dimmable with ELV and/or LED compatible
dimmer switch.
Product Usage Instructions
- Shut off power at the fuse box or circuit breaker box and
remove the old fixture including the mounting hardware. - Unpack the new fixture from the carton and check that all parts
are included as shown in the illustration. - Loosen three screws on keyholes on the mounting plate, then
separate the mounting plate from the canopy. - Attach the mounting plate to the junction box using the
mounting screws. The side of the mounting plate marked GND must
face out. - Determine the desired hanging height by pressing the wire
strainer. Pass wires carefully through the canopy. - Connect the electrical wires as shown in Fig. 2, making sure
that all wire connectors are secured. If your junction box has a
ground wire (green or bare copper), connect the fixture’s ground
wire to it. Otherwise, connect the fixture’s ground wire directly
to the mounting plate using the ground screw provided. - Tuck wire connectors neatly into the junction box.
- Align the canopy to the mounting plate, place keyholes of the
canopy over the three screws previously loosened, turn the canopy
until it locks in place on keyholes, then secure by tightening the
three screws previously loosened. - Return power to the junction box and test the fixture.
CAUTION: When handling the fixture, do not apply pressure to the
LEDs. Hold the fixture by the base or fixture body only.
INSTALLATION INSTRUCTIONS
For P5481/2/3-66A-L
W AR NI NG ! S HU T PO WE R O F F AT F US E OR CI RC UI T BR E AKE R.
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
MOUNTING THE FIXTURE (Fig. 1)
1. Shut off power at the fuse box or circuit breaker box and remove the old fixture including the mounting hardware.
2. Carefully unpack your new fixture from carton and check that all parts are included as shown in illustration.
Fig. 1
Mounting Plate Set #:
A-021-175DA for P5481/2/3-66A-L
-Mounting plate (B) -Ground screw -Mounting screw*2 (D)
3. Loose three screws (E) on key holes (Do not remove), then separate mounting plate (B) from canopy (A).
4. Attach mounting plate (B) to junction box (F) (not included) using mounting screws (D) (Size: #8-32*1/2″L). The side of mounting plate marked “GND” must face out.
5. Determine desired hanging height by pressing wire strainer (G). Pass wires carefully through canopy (A).
.
CONNECTION THE WIRES (Fig. 2)
6. Connect the electrical wires as shown in Fig. 2, making sure that all wire connectors are secured. If your junction box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting plate (B) using the ground screw provided.
7. Tuck wire connectors neatly into the junction box.
FINISHING THE INSTALLATION (Fig. 1)
8. Align canopy (A) to mounting plate (B), place key holes of canopy (A) over the three screws (E) previously loosened, turn canopy (A) until it locks in place on key holes, then secure by tightening the three screws (E) previously loosened.
Your installation is now complete. Return power to the junction box and test the fixture.
CAUTION / ATTENTION: When handling the fixture, do not apply pressure to the LEDs. Hold the fixture by the base or fixture body only.
Fig. 2
FIXTURE WIRES Black or Smooth
FIXTURE WIRES White or Ribbed
FIXTURE WIRES Bare Copper (Ground)
Dimmable with ELV and/or LED compatible dimmer switch.
HOUSE WIRES Black (Hot)
HOUSE WIRES White (Neutral)
HOUSE WIRES Green (Ground)
IMPORTANT: Fixture should be installed by a qualified electrician to ensure proper wiring and installation.
