JYL7120A 38.75 Inch Black Modern Bohemian Iron Linear Integrated LED Pendant
Product Information
The product is a lighting fixture with model number JYL7120A.
Its dimensions are 38.75Lx11.75Wx12-60H. The package includes a
part list and hardware list consisting of wire connectors, ground
screw, mounting bracket, machine screw, mounting screw, canopy, and
the metal plate. The fixture comes with a warning that recommends
installation by a licensed electrician and advises switching off
the main electrical supply from the main fuse box/circuit breaker
before installation. The user manual also includes care and
maintenance instructions for cleaning the inside and outside of the
fixture.
Product Usage Instructions
Preparation
Before beginning assembly of the product, ensure that all parts
are present and in good condition. If any part is missing or
damaged, do not attempt to assemble the product. Estimated assembly
time is 20 minutes.
Assembly
- Fix the mounting bracket (B) to the outlet box with machine
screw (F). - Make wire connections using wire connectors (A) as
follows:
- Connect Hot, Black or Red Outlet Supply Wire to Black Parallel
Cord (round & smooth) Clear, Brown, Gold or Black without
Tracer (colored stripes) Insulated Wire (not green) with copper
metal conductor. - Connect Neutral, White Outlet Supply Wire to White Parallel
Cord (square & ridged) Clear, Brown, Gold or Black with Tracer
(colored stripes) Insulated Wire (not green) with Silver metal
conductor.
Note: When parallel wire (SPT I & SPT II) is used, the
neutral wire is square shaped and ridged, and the hot wire will be
round in shape and smooth.
Grounding Instructions
- For installation in the United States: Wrap the ground wire
from the outlet box around the green ground screw (E) on the
mounting bracket, no less than 2 inches from wire end. Tighten
ground screw. If the fixture is supplied with a ground wire,
connect it to the outlet ground wire with a wire connector. - For installation in Canada: If the fixture is supplied with a
ground wire, wrap it around the green grounding screw on the
mounting bracket. Tighten ground screw.
Care and Maintenance
To clean the outside of the fixture, use a dry or slightly
dampened clean cloth (use clean water, never a solvent) to wipe the
surface of the fixture. To clean the inside of the fixture, first
disconnect power to the fixture by turning off the circuit breaker
or by removing the fuse at the fuse box. Next, use a dry or
slightly dampened clean cloth (use clean water, never a solvent) to
wipe the interior surface of the fixture. Do not use any cleaners
with chemical, solvents, or harsh abrasives. Use only a dry soft
cloth to dust or wipe carefully.
Notice & Important Safety Instructions
- Please make sure that you have all parts indicated before you
begin assembly of this item. - This item should be assembled on a soft surface to prevent
scratching the finish during assembly. - To reduce the risk of fire, electrical shock, or injury to
persons or property, please follow the guideline below for safe use
and installation. - The external flexible cable or cord of this lamp cannot be
replaced. If the cord is damaged, the lamp shall be destroyed.
WARNING
WE RECOMMEND INSTALLATION OF THIS LIGHTING FIXTURE BE DONE BY A LICENSED ELECTRICIAN. WARNING *** SWITCH OFF THE MAIN ELECTRICAL SUPPLY FROM THE MAIN FUSE BOX/CIRCUIT BREAKER BEFORE INSTALLATION. INSPECT ITEM CAREFULLY BEFORE ATTEMPTING TO INSTALL. IF THERE IS ANY DAMAGE OR OBVIOUS DEFECT, DO NOT INSTALL. ITEM MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALLED.
CARE AND MAINTENANCE
To clean the outside of the fixture, use a dry or slightly dampened clean cloth (use clean water, never a solvent) to wipe the surface of the fixture.
To clean the inside of the fixture, first disconnect power to the fixture by turning off the circuit breaker or by removing the fuse at the fuse box. Next, use a dry or slighly damperned clean clorth (use clean water, never a solvent) to wipe the
interior surface of the fixture. Do not use any cleaners with chemical, solvents or harsh abrasives. Use only a dry soft cloth to dust or wipe carefully.
NOTICE & IMPORTANT SAFETY INSTRUCTIONS
* Please make sure that you have all parts indicated before you begin assembly of this item * This item should be assembled on a soft surface to prevent scratching the finish during assembly * To reduce the risk of fire, electrical shock or injury to persons or property, please follow the guideline below for safe use
and installation
* The external flexible cable or cord of this lamp cannot be replaced
If the cord is damaged, the lamp shall be destroyed
Model#:JYL7120A Product Dimensions:38.75″Lx11.75″Wx12-60″H
Part List and Hardware List
PIECE DESCRIPTION PICTURE QUANTITY PIECE DESCRIPTION PICTURE QUANTITY
A wire connector
3X
E
ground screw
1X
mounting
B
bracket
1X
F mounting screw
2X
C machine screw
2X
G the metal plate
2X
D
canopy
1X
12
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product. Estimated Assembly Time: 20 minutes.
1. Fix the mounting bracket(B) to the outlet box with machine screw(F). 2. Make wire connections, with wire connectors(A), following the reference chart listed below.
Connect, Hot, Black or Red Outlet Supply Wire to: Black
* Parallel Cord (round & smooth)
Clear, Brown, Gold or Black without Tracer (colored stripes)
Insulated Wire (not green) with copper metal conductor
Connect, Neutral, White Outlet Supply Wire to: White
* Parallel Cord (square & ridged)
Clear, Brown, Gold or Black with Tracer (colored stripes)
Insulated Wire (not green) with Silver metal conductor
A
E
G
B
F
C
D
*Note: When parallel wire ( SPT I & SPT II ) is used. The neutral wire is square shaped and ridged and the hot wire will be round in shape and smooth. ( See Illustration on left. )
Grounding Instructions:
a) For installation in the United States: Wrap ground wire from outlet box around green ground screw(E) on mounting bracket, no less than 2″ from wire end. Tighten ground screw. If fixture is supplied with a ground wire, connect to outlet ground wire with a wire connector. b) For installation in Canada: If fixture is supplied with ground wire, wrap ground wire around green grounding screw on mounting bracket. Tighten ground screw.
3. Carefully remove packaging from fixture, adjust wire length to desired mounting height, fix the canopy(D) to bracket(B) using machine screw(C).
ENJOY YOUR LAMP
22
