V I V O Stand-v100d Pneumatic Arm Single Ultrawide Monitor Desk Mount Instruction Manual

STAND-V100D Pneumatic Arm Single Ultrawide Monitor Desk Mount

Pneumatic Arm Single Ultrawide Monitor Desk Mount
Instruction Manual

SKU: STAND-V100D
Scan the QR code with your mobile device or follow the link for helpful videos and specifications related to this product. https://vivo-us.com/products/stand-v100d
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

[email protected]

www.vivo-us.com Chat live with an agent!

309-278-5303

WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER: · NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND. · USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
PACKAGE CONTENTS

A (x1) Arm

B (x1) Upper Clamp

C (x1) Lower Clamp

D (x1) VESA Plate

E (x1) Clamp Cable Clip

F (x1) Pad

G (x1) Grommet
Plate

H (x1) Support
Plate

S-A (x1) Spacer

S-B (x1) M8x25mm
Screw

S-C (x4) M6x12mm
Screw

M-A (x4) M4x12mm
Screw

M-B (x4) M5x12mm
Screw

M-C (x4) M5 Washer

T-A (x1) 4mm Allen
Wrench

TOOLS NEEDED

Phillips Screwdriver
2

T-B (x1) 6mm Allen
Wrench
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED

DO NOT EXCEED WEIGHT CAPACITY. 4.4-44 lbs

Failure to do so may result in serious injury.

(2-20 kg)

ASSEMBLY STEPS
STEP 1
Cut the shipping tie from Arm (A) while firmly holding the two halves close together. Slowly release the pressure and allow it to gradually open up to reach full extension.
A

STEP 2: Option A – Desk Clamp
Assemble Upper Clamp (B) to the underside of Arm (A) using M6x12mm Screws (S-C) and 4mm Allen Wrench (T-A). Place Pad (F) to bottom of Upper Clamp (B).

A B

F

T-A

S-C

Loosen bolts on Lower Clamp (C) using 6mm Allen Wrench (T-B). Turn Clamp over and place Support Plate (H) over bolt ends.
H
T-B

C
Slightly loosen back side screws on Lower Clamp (C), allowing 6mm to be exposed. Slide Lower Clamp (C) into the appropriate keyholes of Upper Clamp (B) based on desktop thickness. Use lower holes for desktops 50-85mm (2″ to 3 3/8″) thick, and upper holes for desktops 10-58mm (3/8″ to 2 1/4″).

C B 3

STEP 2: Option A – Desk Clamp – Continued
Secure screws on Lower Clamp (C) using 4mm Allen Wrench (T-A). Tighten lower bolts on Lower Clamp (C) to secure to desktop using 6 mm Allen Wrench (T-B).
C T-A
C T-B
Proceed to Step 3 at the bottom of Page 5
STEP 2: Option B – Grommet
Assemble Grommet Plate (G) to under side of Arm (A) using M6x12mm Screws (S-C) and 4mm Allen Wrench (T-A). Apply Pad (F) to Grommet Plate (G).
A

G

F

T-A

S-C

Remove Bolts (C1) from Lower Clamp (C) using 6mm Allen Wrench (T-B). Insert one Bolt (C1) into middle hole of Support Plate (H).

C1 C1
C H
4

STEP 2: Option B – Grommet – Continued
If you are using an existing grommet hole, ensure that it is at least 10mm (3/8″) in diameter and no more than 60mm (2 3/8″). Desktop should be between 10mm-48mm (3/8″ to 1 7/8″) . For desktops without an existing gromment hole, use a 3/8″ (10mm) drill bit to drill through desktop.

EXISTING GROMMET HOLE

DRILLING A GROMMET HOLE

Place mount asembly over gromment hole and secure to desktop using Support Plate (H), Bolt (C1), and 6mm Allen Wrench (T-B).
H C1
T-B
STEP 3
Connect VESA Plate (D) to Arm (A) using Spacer (S-A), M8x25mm Screw (S-B), and 6mm Allen Wrench (T-B). Ensure that hexagon side of space is facing upward towards VESA Plate (D). Remove Thumbscrew (D1) from back of VESA Plate (D). Separate Front VESA Plate (D2) from Back VESA Plate (D3). Set aside.

D A

D2

D1

D3

S-A
S-B T-B

5

STEP 4
Connect Front VESA Plate (D2) to back of Monitor using appropriate Screws (M-A, M-B), M5 Washers (M-C), and a Phillips Screwdriver.

M-A

D2

M-B

M-C

STEP 5
To mount the monitor, begin by lining up the tabs on Front VESA Plate (D2) with the slots on Back VESA Plate (D3). Insert tabs into slots and re-install Thumbscrew (D1) into Back VESA Plate (D3) to secure.
D3 D2

D1
STEP 6
While holding the arm in the horizontal position, adjust the gas spring tension using 6mm Allen Wrench (T-B).
How to adjust if… T-B
ARM DROPS – If the arm drops, turn the adjustment screw counter clockwise until it holds the monitor in a horizontal position.

CAUTION – To avoid damage to the monitor and mount, always keep the arm in a horizontal position while making adjustments.
6

ARM RISES – If the arm raises up, turn the adjustment screw lockwise until it holds the monitor in a horizontal position.

STEP 7
Remove Cable Cover (A1) from Arm (A) by sliding it forward. Route cables and replace Cover (A1). Place Clamp Cable Clip (E) onto backside of assembly for additional cable management. 4mm and 6mm Allen Wrenches (T-A, T-B) can be stored in slots for future adjustments.

T-A

A

T-B

E
A1
STEP 8
To keep mount stable, do not extend arm fully behind desktop edge.
X

Adjust the tilt using the 6mm Allen Wrench (T-B).
T-B Adjust the monitor position as desired.

7

Love your new VIVO setup and want to share? Tag us in your photo! @vivo_us

LAST UPDATED: 11/15/2022 REV1

Open Monday – Friday 7:00am – 7:00pm CST, our dedicated support team can offer immediate assistance with rapid response times. If any parts are received damaged or defective, please contact us. We are happy to replace parts to ensure you have a fully functioning product.

309-278-5303

AVG. RESOLUTION TIME (within office hrs): 5M 4S

www.vivo-us.com
Chat live with an agent!

AVG. RESOLUTION TIME (within office hrs): < 15 M

[email protected]

AVG. RESPONSE TIME (within office hrs): 1HR 8M – 23% within < 15m – 38% within < 30m – 61% within < 1hr – 83% within < 2hr – 92% within < 3hr

FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com

References

• Register a .US.COM domain today!
• VIVO - Desks, Monitor Mounting, and More Home & Office Solutions – VIVO - desk solutions, screen mounting, and more