V I V O Stand-v101h Pneumatic Arm Single Monitor Desk Mount Instruction Manual

STAND-V101H Pneumatic Arm Single Monitor Desk Mount

Pneumatic Arm Single Monitor Desk Mount
Instruction Manual

SKU: STAND-V101H
Scan the QR code with your mobile device or follow the link for helpful videos and specifications related to this product. https://vivo-us.com/products/stand-v101h
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

[email protected]

www.vivo-us.com Chat live with an agent!

309-278-5303

WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.
WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
PACKAGE CONTENTS

A (x1) Monitor Arm

B (x1) Clamp

C (x1) Clamp Brace

D (x1) Grommet Base

E (x1) Pole

F (x1) Base Cover

G (x1) VESA Plate

H (x1) Support Plate

I (x1) Cable Clip

J (x5) Rubber Pad

S-A (x2) M6x10mm Screw

S-B (x1) Thumbscrew

M-A (x4) M4x12mm Screw

M-B (x4) M4x16mm Screw

M-C (x4) M5x12mm Screw

M-D (x4) M5x16mm Screw

M-E (x4) M5 Washer

M-F (x4) Spacer

T-A (x1)

T-B (x1)

3mm Allen Wrench 4mm Allen Wrench

T-C (x1) 6mm Allen Wrench
FOR VESA ADAPTER:

K (x1) Adapter Plate

S-C (x4) M4x12mm Screw

2

S-D (x4) M4 Nut

S-E (x8) M5 Washer
NOTE: SOME HARDWARE MAY NOT BE USED

TOOLS NEEDED

Phillips Screwdriver

Wrench

ASSEMBLY STEPS
STEP 1
Slide Base Cover (F) onto Pole (E).

E

DO NOT EXCEED WEIGHT CAPACITY.

Failure to do so may result in serious injury.

4-26.4lbs (1.81-11.97kg)

STEP 2
Stick Rubber Pads (J) to the underside of Clamp Brace (C). (Skip to Step 3 Option B if grommet base option will be used)
C
J
F

STEP 3 (Option A)

Clamp Installation

Assemble Clamp (B) to Clamp Brace

(C) using M6x8mm Screws (S-A)

C

and tighten with 4mm Allen Wrench (T-B). Thread Pole (E) onto Clamp

S-A

Brace (C), and tighten pre-installed

set screws with 3mm Allen Wrench T-B (T-A). Press Base Cover (F) into place. Place assembly on the edge

of the desk and tighten the hand bolt to secure.

E

F

10-88m m

T-A 3

STEP 3 (Option B)
Grommet Base Installation Thread Pole (E) onto Grommet Base (D), tighten pre-installed set screws with 3mm Allen Wrench (T-A), and press Base Cover (F) into place. Stick Rubber Pads (J) to the underside of Grommet Base (D). Remove screw from end of Hand Bolt (B1) on Clamp (B) and separate parts. Use Hand Bolt (B1) with Support Plate (H) to secure base assembly to grommet hole in desk.
E F
T-A D
J

10-85mm

B B1 H
STEP 4
Slide Cable Clip (I) and Monitor Arm (A) onto Pole (E). Secure Monitor Arm (A) using 6mm Allen Wrench (T-C).

I

A

E T-C

4

STEP 5
OPTION A: Flat Back Monitor For flat back monitors, install VESA Plate (G) to monitor using Screws (M-A) or (M-C) and M5 Washers (M-E).
OPTION B: Curved Back Monitor For curved back monitors, install VESA Plate (G) to monitor using Screws (M-B) or (M-D), M5 Washers (M-E), and Spacers (M-F).
G

TV

TV

TV

TV

M- A M- C
M- E

M- B M- D M- E
M- F

FOR VESA ADAPTER:
If your monitor has a 200×100 VESA hole pattern, install Adapter Plate (K) to VESA Plate (G) using M4x12mm Screws (S-C), M4 Nuts (S-D), and M5 Washers (S-E). Install Adapter Plate (A) to the monitor using Screws (M-A through M-D) and M5 Washers (M-E).

K S-C

G S-ES-D

M-E

M-A through M-D

5

STEP 6
Slide VESA Plate (G) over bracket on Monitor Arm (A). Secure using Thumbscrew (S-B).

S-BL

A

G

STEP 7
Remove bottom cover from Monitor Arm (A) by sliding cover forward and off.
A

STEP 8
Run cables through bottom of Monitor Arm (A). Reattach cover.
A
6

STEP 9
Adjust tension in Monitor Arm (A) and angle of monitor using 6mm Allen Wrench (T-C). Clockwise reduces tension, counterclockwise increases tension. The tension should be just enough to hold your monitor in place without lifting itself up.

T-C

A

T-C

STEP 10
Adjust monitor to desired position and store Allen Wrenches (T-A, T-B, T-C) in Cable Clip (I) for future adjustments.

T-C

T-A

I

T-B

±115°

±180°

±90° ±180°

+35° -35°

7

Love your new VIVO setup and want to share? Tag us in your photo! @vivo_us

LAST UPDATED: 08/18/2022 REV1

Open Monday – Friday 7:00am – 7:00pm CST, our dedicated support team can offer immediate assistance with rapid response times. If any parts are received damaged or defective, please contact us. We are happy to replace parts to ensure you have a fully functioning product.

309-278-5303

AVG. RESOLUTION TIME (within office hrs): 5M 4S

www.vivo-us.com
Chat live with an agent!

AVG. RESOLUTION TIME (within office hrs): < 15 M

[email protected]

AVG. RESPONSE TIME (within office hrs): 1HR 8M – 23% within < 15m – 38% within < 30m – 61% within < 1hr – 83% within < 2hr – 92% within < 3hr

FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com

References

• Register a .US.COM domain today!
• VIVO - Desks, Monitor Mounting, and More Home & Office Solutions – VIVO - desk solutions, screen mounting, and more
• Pneumatic Arm Single Monitor Desk Mount – VIVO - desk solutions, screen mounting, and more