2959-572 Upham Estates 10-Light Coal and Polished Nickel Island Chandelier
Product Information
The item number for this product is 2959-572, and it was
manufactured on August 18, 2021. The product comes with
installation instructions that should be read and saved for future
reference. This fixture requires a power source and should be
installed by a professional electrician. The maximum wattage rating
for this fixture is 60 watts.
Product Usage Instructions
Before starting the installation process, shut off the power at
the fuse box or circuit breaker box. Remove the old fixture and
mounting hardware, then unpack the new fixture and lay out all the
parts in a clean area.
To assemble the fixture, first, loosen the hex nuts on the
canopy with a wrench and remove the metal washer, lock washer,
canopy, and swivels. Next, place the cloth shade and metal washer
over all thread. Determine the desired hanging height and thread
the rods to all thread of fixture body. Pass wires through each rod
during assembly and secure swivels onto rods. Slide canopy and
metal plate followed by lock washer and metal washer onto swivels
and secure with hex nuts via wrench.
Position the mounting plate on the ceiling and mark the location
of the two drywall anchors. Pre-drill holes for drywall anchors,
then insert drywall anchors into the ceiling. Attach the mounting
plate to a junction box using mounting screws and wood screws into
drywall anchors. The side of the mounting plate marked GND must
face out.
To connect the wires, follow the instructions shown in Fig. 2,
making sure that all wire connectors are secured. If your junction
box has a ground wire (green or bare copper), connect the fixture’s
ground wire to it. Otherwise, connect the fixture’s ground wire
directly to the mounting plate using the green screw provided. Tuck
wire connectors neatly into the junction box.
To complete the installation, slide the canopy over the mounting
plate and secure it with screws. Place candle covers over sockets,
and install ten candelabra base bulbs up to 60 watts each or CFL or
LED equivalent (not included) in accordance with the fixture
specification. Do not exceed the maximum wattage rating. The
installation is now complete. Return power to the junction box and
test the fixture.
INSTALLATION INSTRUCTIONS
Item#2959-572 (New. 2021/08/18) READ AND SAVE THESE INSTRUCTIONS
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
PREPARATION (Fig. 1)
Fig. 1
1. Shut off power at the fuse box or circuit breaker box and Set# A-021-220115
remove the old fixture including the mounting hardware.
-Mounting plate
2. Carefully unpack your new fixture and lay out all the parts in a -Ground screw
clean area. Take care not to misplace any small parts -Mounting screw*2
necessary for installation.
K
ASSEMBLING THE FIXTURE (Fig. 1)
3. Loosen hex nuts (D) on canopy (H) with wrench (J) (not
O
A
included) and remove metal washer (E), lock washer (L), canopy (H) and swivels (G). 4. Place cloth shade (N) and metal washer (M) over all thread (T).
D
B
E
L I
J
5. Determine the desired hanging height and thread rods (F1, F2
C
and F3) to all thread (T) of fixture body. Carefully pass wires
H
through each rod during assembly. Secure swivels (G) onto Rod# W30-1-66A*2(F1)
G
rods (F1). 6. Slide canopy (H) and metal plate (I) followed by lock washer
W30-1-66A *4(F2) W30-H-66A *2(F3)
F1
(L) and metal washer (E) onto swivels (G) and secure with
hex nuts (D) via wrench (J) (not included).
F2
7. Position mounting plate (A) on ceiling and mark the location of
the two drywall anchors (K). Pre-drill holes for drywall
F3
anchors (K). Then insert drywall anchors (K) into ceiling.
M
8. Attach mounting plate (A) to junction box (not included) using
mounting screws (B) (Size: #8-32N*L0.5″) and wood screws
N
(O) into drywall anchors (K). The side of the mounting plate
marked “GND” must face out.
CONNECTING THE WIRES (Fig. 2)
9. Connect the electrical wires as shown in Fig. 2, making sure
that all wire connectors are secured. If your junction box has
a ground wire (green or bare copper), connect the fixture’s
T
ground wire to it. Otherwise, connect the fixture’s ground
wire directly to the mounting plate (A) using the green screw
P
provided.
Q
10. Tuck wire connectors neatly into junction box.
COMPLETING THE INSTALLATION (Fig. 1)
R
11. Slide canopy (H) over mounting plate (A) and secure with
screws (C).
12. Place candle covers (Q) over sockets (R).
13. Install (10) ten candelabra base bulbs (P) up to 60 watts Candle cover#CCV21058P-613 each or CFL or LED equivalent (not included) in accordance
with the fixture specification–DO NOT EXCEED THE
MAXIMUM WATTAGE RATING! (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!)
Your installation is now complete. Return power to the junction box and test the fixture.
Fig. 2
FIXTURE WIRES Black or Smooth
FIXTURE WIRES White or Ribbed
FIXTURE WIRES Bare Copper (Ground)
Note: Illustration (Fig. 1) on this manual is for installation purposes only. It may or may not be identical to the fixture purchased.
HOUSE WIRES Black (Hot)
HOUSE WIRES White (Neutral)
HOUSE WIRES Green (Ground)
Page:1/1
LA-3483E
