3994-66A Beckonridge Chandelier
Product Information
The product is a chandelier with two models: Item#3994-66A and
Item#3994-84. The chandelier is designed for rod hang installation.
The package includes a mounting plate, ground screw, mounting
screws, fixture body, cap, coupling, rods, loop, quick link,
mounting screw, canopy, finials, glasses, socket rings, and shade.
The chandelier can hold up to 4 medium base bulbs with a maximum
wattage rating of 60 watts each or equivalent CFL or LED bulbs.
Product Usage Instructions
- Shut off power at the fuse box or circuit breaker box before
starting the installation process. - Remove the old fixture and mounting hardware.
- Un-thread the metal part on top of the center bar and
decorative part on the bottom of the center bar. Pull out wires and
connectors from the center bar, loosen the wires by unscrewing wire
connectors, twist wires as one strand. Carefully put the rod
through the center bar and do not twist with other wires inside the
center bar. Turnover fixture body with sockets facing upward,
re-connect the wires, tuck wires and connectors neatly into the
center bar. Secure metal part and decorative part back into center
bar. - Place cap on all thread of fixture body and secure with
coupling. - Determine desired hanging height and thread rods to all thread
of fixture body. Pass wires through each rod as you assemble. - Thread loop onto rod, attach quick link to loop and loop.
Carefully feed wires through loop, quick link, and loop. Note: The
quick link must be fully closed. - Thread mounting screw into pre-drilled holes in mounting plate
spaced same distance apart as holes in the canopy. Length of
mounting screws may be adjusted if necessary. Attach mounting plate
to junction box using the junction box screws. The side of mounting
plate marked GND must face out. - Connect electrical wires as shown in the diagram, making sure
that all wire connectors are secured. If your junction box has a
ground wire, connect the fixture’s ground wire to it. Otherwise,
connect the ground wire directly to the mounting plate using the
green screw provided. - Tuck wire connectors neatly into the junction box.
- Place canopy over mounting plate and secure with finials.
- Remove socket ring rings from sockets and place glasses over
sockets and secure with socket rings. - Install up to 4 medium base bulbs or equivalent CFL or LED
bulbs in accordance with the fixture specification. Do not exceed
the maximum wattage rating. - Turn on power and test the chandelier.
INSTALLATION INSTRUCTIONS
Item#3994-66A/3994-84(Chandelier For Rod hang) READ AND SAVE THESE INSTRUCTIONS
W AR NI N G ! S HU T P O WE R O F F AT F U S E O R CI R C UI T B R E AK E R .
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
1. Shut off power at the fuse box or circuit breaker box and remove the old fixture including the mounting hardware. 2. Carefully unpack your new fixture and lay out all the parts in a clean area. Take care not to misplace any small parts necessary for installation. ASSEMBLING THE FIXTURE (Fig.1) Noted: To install the fixture as an upward option, follow step 3, if not, please proceed
Fig.1
Set#A-020 -Mounting plate -Ground Screw -Mounting Screw*2
to step 4.
3. Un-thread metal part (R) on top of center bar (S) and decorative part (Q) on
bottom of center bar (S). Carefully pull out wires and connectors from center bar (S),
loosen wires by unscrewing wire connectors, twist wires as one strand. Carefully put Rod#W32-H-66A & W32-1-66A for 3994-66A
strand through center bar (S) and do not twist with other wires inside center bar (S). Rod#W32-H-84 & W32-1-84 for 3994-84 G
Then turnover fixture body (M) with sockets facing upward, re-connect the wires,
tuck wires and connectors neatly into center bar (S). Secure metal part (R) and
decorative part (Q) back into center bar (S). (Fig.1)
4. Place cap (L) on all thread of fixture body (M) and secure with coupling (K).
5. Determine desired hanging height and thread rods (J and I) to all thread of fixture
body (M). Pass wires carefully through each rod as you assemble.
6. Thread loop (G1) onto rod (I), attach quick link (H) to loop (G1) and loop (G).
Carefully feed wires through loop (G1), quick link (H) and loop (G). Note: The quick
link (H) must be fully closed.
7. Thread mounting screw (D) into pre-drilled holes in mounting plate (A) spaced
S
same distance apart as holes in canopy (C). Length of mounting screws (D) may be adjusted if necessary. Attached mounting plate (A) to junction box (Not included)
R
S
using the junction box screws (B). The side of mounting plate marked “GND” must
face out.
Q
CONNECTING THE WIRES (Fig. 2)
8. Connect electrical wires as shown in Fig.2, making sure that all wire connectors
L
are secured. If your junction box has a ground wire (green or bare copper), connect
the fixture’s ground wire to it. Otherwise, connect the ground wire directly to the
mounting plate (A) using the green screw (E) provided.
9. Tuck wire connectors neatly into the junction box.
COMPLETING THE INSTALLATION (Fig. 1)
10. Place canopy (C) over mounting plate (A) and secure with finials (F). 1.. Remove socket ring rings (O) from sockets and place glasses (N) over sockets and secure with socket rings (O).
Shade#G3994-2 for 3994-84 Shade#G3994-1for 3994-66A
12. Install (4) four medium base bulbs (P) up to 60 watts each or CFL or LED
equivalent (not included) in accordance with the fixture specification–DO NOT
EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!)
Your installation is now complete. Return power to the junction box and test the
Fig. 2
FIXTURE WIRES Black or Smooth
FIXTURE WIRES White or Ribbed
fixture.
D A E B C F H G1 I
J
K R S Q
FIXTURE WIRES Bare Copper (Ground)
Note: Illustration (Fig. 1) on this manual is f installation purposes only. It may or may not be identical to the fixture purchased.
HOUSE WIRES Black (Hot)
HOUSE WIRES White (Neutral)
IMPORTANT: FIXTURE SHOULD BE INSTALLED BY A QUALIFIED ELECTRICIAN TO ENSURE PROPER WIRING AND INSTALLATION.
M N O P
HOUSE WIRES Green (Ground)
Fig.3
D A E B
a. Hardware Bag:
A. Mounting plate*1 B. Junction Box Screw*2 C. Canopy *1 D. Mounting screw*2 E. Ground screw*1 F. Finial*2 G1. Loop*1 H. Quick Link*1
b. Hardware Bag: J. ROD 12″*3 I. ROD 6″*1
G
C F
H
A
C F H D B E G1
J
I
2/3 Page: 2/2
