3995-66A Beckonridge Chandelier
Product Information
The product is a chandelier designed for rod hang. It is
available in two variants – Item#3995-66A and Item#3995-84. The
package includes a mounting plate, ground screw, mounting screw,
rod, shade, and fixture wires. The fixture wires are available in
black or smooth, white or ribbed, and bare copper (ground)
variants. The installation must be done by a qualified electrician
to ensure proper wiring and installation.
Product Usage Instructions
- Before starting the installation process, turn off the power at
the fuse or circuit breaker. This is a safety precaution that must
be followed strictly. - Begin by mounting the chandelier on the provided mounting plate
using the ground screw and mounting screws. Refer to Fig.1 for the
hardware arrangement. - For Item#3995-66A, use Rod#W32-H-66A & W32-1-66A, and for
Item#3995-84, use Rod#W32-H-84 & W32-1-84 to hang the
chandelier. Refer to Fig.1 for the hardware arrangement. - Attach the shade to the chandelier using Shade#G3994-2 for
Item#3995-84 and Shade#G3994-1 for Item#3995-66A. Refer to Fig.1
for the hardware arrangement. - Connect the fixture wires to the house wires. The black or
smooth fixture wire should be connected to the black (hot) house
wire, the white or ribbed fixture wire should be connected to the
white (neutral) house wire, and the bare copper fixture wire should
be connected to the green (ground) house wire. Refer to Fig.2 for
the hardware arrangement. - Once all the connections are made, return power to the junction
box and test the fixture. Ensure that it is working properly before
completing the installation process. - Note that the illustration in Fig.1 is for installation
purposes only and may or may not be identical to the fixture
purchased.
INSTALLATION INSTRUCTIONS
Item#3995-66A/3995-84(Chandelier For Rod Hang) READ AND SAVE THESE INSTRUCTIONS
W AR NI N G ! S HU T P O WE R O F F AT F U S E O R CI R C UI T B R E AK E R .
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
PREPARATION (Fig. 1) 1. Shut off power at the fuse box or circuit breaker box and remove the old fixture including the mounting hardware. 2. Carefully unpack your new fixture and lay out all the parts in a clean area. Take care not to misplace any small parts necessary for installation. ASSEMBLING THE FIXTURE (Fig.1) Noted: To install the fixture as an upward option, follow step 3, if not, please proceed to step 4. 3. Un-thread metal part (U) on top of center bar (T), remove decorative finial (S), nut (R) and metal washer (Q) on bottom of center bar (T). Carefully pull out wires and connectors from center bar (T). Loosen wires by removing wire connectors, twist wires as one strand. Carefully put strand through center bar (T) and do not twist with other wires inside center bar (T). Turnover the fixture body (L) with sockets facing upward, re-connect wires, tuck wires and connectors neatly into center bar (T), secure metal part (U), metal washer (Q), nut (R) and finial (S) back into center bar (T). (Fig.1) 4. Place cap (K) on all thread of fixture body (L) and secure with coupling (J). 5. Determine desired hanging height and thread rods (I and H) to all thread of fixture body (L). Pass wires carefully through each rod as you assemble. 6. Thread loop (G1) onto rod (H), attach quick link (P) to loop (G1) and loop (G). Carefully feed wires through loop (G1), quick link (P) and loop (G). Note: The quick link (P) must be fully closed. 7. Thread mounting screw (D) into pre-drilled holes in mounting plate (A) spaced same distance apart as holes in canopy (C). Length of mounting screws (D) may be adjusted if necessary. Attached mounting plate (A) to junction box (Not included) using junction box screws (B). The side of mounting plate marked “GND” must face out. CONNECTING THE WIRES (Fig.2) 8. Connect the electrical wires as shown in fig 2, making sure that all wire connectors are secured. If your junction box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting plate (A) using the green screw provided. 9. Tuck wire connectors neatly into the junction box. COMPLETING THE INSTALLATION (Fig. 1) 10. Place canopy (C) over mounting plate (A) and secure with two finials (F) onto mounting screws (D). 11. Remove socket rings (N) from sockets and place glasses (M) over sockets and secure with socket rings (N). 12. Install (5) five medium base bulbs (O) up to 60 watts each or CFL or LED equivalent (not included) in accordance with the fixture specification–DO NOT EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!)
Your installation is now complete. Return power to the junction box and test the fixture.
Fig.1
Set#A-020 -Mounting plate -Ground Screw -Mounting Screw*2
G P
Rod#W32-H-66A & W32-1-66A for 3995-66A
Rod#W32-H-84 & W32-1-84 for 3995-84
T
U
T L
R
Q
S
J
K
U
T
Shade#G3994-2 for 3995-84 Shade#G3994-1 for 3995-66A
Fig. 2
FIXTURE WIRES Black or Smooth
FIXTURE WIRES White or Ribbed
C F G1 H
I L
FIXTURE WIRES Bare Copper (Ground)
Note: Illustration (Fig. 1) on this manual is f installation purposes only. It may or may not be identical to the fixture purchased.
HOUSE WIRES Black (Hot)
HOUSE WIRES White (Neutral)
IMPORTANT: FIXTURE SHOULD BE INSTALLED BY A QUALIFIED ELECTRICIAN TO ENSURE PROPER WIRING AND INSTALLATION.
M N O
HOUSE WIRES Green (Ground)
Fig.3
G P
a. Hardware Bag: A. Mounting plate*1 B. Junction Box Screw*2 C. Canopy *1 D. Mounting screw*2 E. Ground screw*1 F. Finial*2 G1. Loop*1 P. Quick Link*1
b. Hardware Bag: I. ROD 12″*3 H. ROD 6″*1
Page: 2/3
Page: 2/2
D A E B C F
A
C F P E D B G1
I
H
