Product Information:

The product is a ceiling light fixture with item number
2899-691. The installation instructions were last updated on August
18, 2021. The fixture requires a power source and should be
installed by a professional electrician. The fixture can support up
to nine candelabra base bulbs, with a maximum wattage of 60 watts
each. The fixture comes with mounting hardware, ground screw, and
support cable to assist with installation.

Product Usage Instructions:

Before installing the fixture, shut off power at the fuse box
or circuit breaker box.
Remove the old fixture including the mounting hardware.
Unpack the new fixture and lay out all the parts in a clean
area.
Determine the desired hanging height and thread rods (F1, F2,
and F3) to all thread (J) on top of fixture body. Attach canopy (D)
by threading onto rod (F1). Feed wires through each rod as you
assemble. Remove all thread if installing with one 6 rod only.
Attach mounting plate (A) to the junction box (not included)
with mounting screws (B). The side of the mounting plate (A) marked
GND and two convex points must face out.
Connect the electrical wires as shown in Fig. 2, making sure
that all wire connectors are secured. If your junction box has a
ground wire (green or bare copper), connect the fixture’s ground
wire to it. Otherwise, connect the fixture’s ground wire directly
to the mounting plate (A) using the green screw provided. Tuck wire
connectors neatly into the junction box.
Slide canopy (D) over mounting plate (A) and secure with screws
(E).
Install nine candelabra base bulbs (H) up to 60 watts each or
CFL or LED equivalent (not included) in accordance with the fixture
specification. DO NOT EXCEED THE MAXIMUM WATTAGE RATING!
Screw glass shades (I) onto socket cups (G).
Return power to the junction box and test the fixture.

View Fullscreen

INSTALLATION INSTRUCTIONS

Item#2899-691 (New. 2021/08/18) READ AND SAVE THESE INSTRUCTIONS
W AR NI N G ! S HU T P O WE R O F F AT F U S E O R CI R C UI T B R E AK E R .

AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.

MOUNTING THE FIXTURE (Fig.1)

Fig. 1

1. Shut off power at the fuse box or circuit breaker box and Set# A-021-118DH

remove the old fixture including the mounting hardware.

-Mounting plate

2. Carefully unpack your new fixture and lay out all the parts -Ground screw in a clean area. Take care not to misplace any small parts -Mounting screws*2

necessary for installation.

3. Determine the desired hanging height and thread rods (F1,

F2 and F3) to all thread (J) on top of fixture body. Attach

canopy (D) by threading onto rod (F1). Carefully feed wires

through each rod as you assemble. Note: Remove all

thread, if installing with one 6″ rod only.

4. Attach mounting plate (A) to the junction box (Not included)

with mounting screws (B) (Size: #8-32N*L0.5″). The side of

the mounting plate (A) marked “GND” and two convex

points must face out.

5. The support cable is provided to support weight of fixture

while wiring. Align the fixture to mounting plate (A) and attach hook (P) on the end of support cable (C) to a slot located on mounting plate (A). Carefully allow the support

F3 J

cable (C) to support weight of the fixture while wiring.

CONNECTING THE WIRES (Fig. 2)

6. Connect the electrical wires as shown in fig 2, making sure

that all wire connectors are secured. If your junction box

has a ground wire (green or bare copper), connect the

fixture’s ground wire to it. Otherwise, connect the fixture’s

ground wire directly to the mounting plate (A) using the

green screw provided.

7. Tuck wire connectors neatly into the junction box.

COMPLETING THE INSTALLATION (Fig. 1)

8. Slide canopy (D) over mounting plate (A) and secure with