4046-84 6-Light Brushed Nickel Candlestick Chandelier
Product Information
The product being installed is item #4046-84, with a release
date of 06/25/2021. This product is a light fixture that requires
wiring and installation. The installation process involves
connecting the electrical wires, securing the wire connections,
installing the fixture screws, placing the glass shade, and
installing the bulbs.
The fixture is designed to use (6) six medium base (E26) bulbs
with a maximum wattage of 60 watts each. CFL or LED equivalent
bulbs can also be used but are not included in the package. The
fixture specification should be followed to avoid exceeding the
maximum wattage rating.
Product Usage Instructions
Before beginning the installation process, ensure that the power
source is turned off by shutting down the fuse or circuit
breaker.
Connecting the Wires
- Connect the electrical wires according to Fig.3. Ensure that
all wire connectors (D) are secured. - If your outlet box has a ground wire (green or bare copper),
connect the fixture’s ground wire to it. Otherwise, connect the
fixture’s ground wire directly to the mounting plate (B) using the
green screw provided. - Tuck wire connections neatly inside the outlet box (A).
Finishing the Installation
- Thread fixture screws (F) through canopy (E) and into mounting
plate (B) and secure. - Place glass shade (K) over socket cups (J). Secure glass shade
(K) using metal rings (L). - Install (6) six medium base (E26) bulbs (M) up to 60 watts each
or CFL or LED equivalent (not included) in accordance with the
fixture specification–DO NOT EXCEED THE MAXIMUM WATTAGE RATING!
(NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!).
Once the installation is complete, return power and test the
fixture. Note that the illustration in Fig.1 may differ from the
actual fixture purchased.
INSTALLATION INSTRUCTIONS
Item#4046-84 (New. 06/25/2021) READ AND SAVE THESE INSTRUCTIONS
W ARNI N G ! SHUT P O WE R O FF AT F US E O R CI RC UI T BRE AK E R.
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
MOUNTING THE FIXTURE (Fig.1) 1. Shut off power at the fuse box or circuit breaker and remove the old fixture included the mounting hardware. 2. Carefully unpack your new fixture and lay out all the parts on a clean area. Take care not to lose any small parts necessary for installation. 3. Adjust position of each lamp arm. (As shown in Fig.2) 4. Place mounting plate (B) over outlet box (A) (Not included) and align mounting slots with mounting holes of outlet box (A). Feed mounting screws (C) through mounting slots of mounting plate (B) and mounting holes of outlet box (A). Make sure the side of the mounting plate (B) marked “GND” must face out. 5. Determine desired hanging height and thread rods (I1 and I2) to the all thread of the fixture body. Screw loop (H1) onto rod (I1). Pass wires carefully through each rod as you assemble. 6. Attach quick link (G) to loop (H1) and loop (H2) on canopy (E). Carefully feed wire through loop (H1), quick link (G), and loop (H2).
CONNECTING THE WIRES (Fig.3) 7. Connect the electrical wires as shown in Fig.3, making sure that all wire connectors (D) are secured. If your outlet box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting plate (B) using the green screw provided. 8. Tuck wire connections neatly inside the outlet box (A).
FINISHING THE INSTALLATION (Fig.1) 9. Thread fixture screws (F) through canopy (E) and into mounting plate (B) and secure.
10. Place glass shade (K) over socket cups (J). Secure glass shade (K) using metal rings (L).
11. Install (6) six medium base (E26) bulbs (M) up to 60 watts each or CFL or LED equivalent (not included) in accordance with the fixture specification–DO NOT
EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS
DEPASSER LA PUISSANCE NOMINALE MAXIMALE!).
Fig.1
Set# A-016
-Mounting Plate
-Ground Screw
-Mounting Screw*2
Your installation is now complete. Return power and test the fixture.
Note: Illustration (Fig.1) on this manual is for installation purposes only. It may or may not be identical to the fixture purchased.
Fig.3
FIXTURE WIRES Black or Smooth
FIXTURE WIRES White or Ribbed HOUSE WIRES Black (Hot)
FIXTURE WIRES Green or Bare Copper (Ground) HOUSE WIRES White (Neutral)
HOUSE WIRES Green (Ground)
4046-84
