2783-695 Chelsea 3-Light Soft Brass Chandelier
Product Information
The product is a fixture with item number 2783-695. It was
manufactured on January 20, 2022. The installation instructions
should be read and saved. The fixture is designed to be mounted on
a junction box with a maximum wattage rating of 60 watts per
bulb.
Product Usage Instructions
- Shut off power at the fuse box or circuit breaker box and
remove the old fixture including the mounting hardware. - Carefully unpack your new fixture and lay out all the parts in
a clean area. Take care not to misplace any small parts necessary
for installation. - Secure rod (H) onto all thread (I) on fixture body.
- Place rod assembly (G) over all thread (E) on rod (H).
Carefully pass the wires through rod (H) during assembly. - Determine the desired hanging height and thread rods (F1, F2,
and F3) to the all thread (E) of rod (H). Attach canopy (C) by
threading onto rod (F1). Carefully feed wires through each rod as
you assemble. Note: Remove all thread, if installing with one 6 rod
only. - Attach mounting plate (A) to junction box with mounting screws
(B) (Size: #8-32N*L0.5). The side of the mounting plate (A) marked
GND and two convex points must face out. - Connect the electrical wires as shown in fig 2, making sure
that all wire connectors are secured. If your junction box has a
ground wire (green or bare copper), connect the fixture’s ground
wire to it. Otherwise, connect the fixture’s ground wire directly
to the mounting plate (A) using the green screw provided. - Tuck wire connectors neatly into the junction box.
- Place canopy (C) over mounting plate (A) and secure with screws
(D). - Place candle covers (K) over sockets (J).
- Place cloth shade (L) onto candle cover (K). Adjust cloth shade
if necessary. - Install (3) three candelabra base bulbs (M) up to 60 watts each
or CFL or LED equivalent (not included) in accordance with the
fixture specification–DO NOT EXCEED THE MAXIMUM WATTAGE
RATING! - Return power to the junction box and test the fixture.
INSTALLATION INSTRUCTIONS
Item#2783-695 (New. 2022/01/20) READ AND SAVE THESE INSTRUCTIONS
W AR NI N G ! S HU T P O WE R O F F AT F U S E O R CI R C UI T B R E AK E R .
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
MOUNTING THE FIXTURE (Fig.1)
Fig. 1
1. Shut off power at the fuse box or circuit breaker box and Set# A-021-118DH
remove the old fixture including the mounting hardware.
-Mounting plate
2. Carefully unpack your new fixture and lay out all the parts -Ground screw
A
in a clean area. Take care not to misplace any small parts -Mounting screws*2 B
necessary for installation.
C
3. Secure rod (H) onto all thread (I) on fixture body.
4. Place rod assembly (G) over all thread (E) on rod (H).
D
Carefully pass the wires through rod (H) during assembly.
F1
5. Determine the desired hanging height and thread rods (F1,
F2 and F3) to the all thread (E) of rod (H). Attach canopy
(C) by threading onto rod (F1). Carefully feed wires through
each rod as you assemble. Note: Remove all thread, if
F2
installing with one 6″ rod only.
F3
6. Attach mounting plate (A) to junction box (Not included)
with mounting screws (B) (Size: #8-32N*L0.5″). The side of
the mounting plate (A) marked “GND” and two convex
points must face out.
CONNECTING THE WIRES (Fig. 2)
7. Connect the electrical wires as shown in fig 2, making sure
that all wire connectors are secured. If your junction box
has a ground wire (green or bare copper), connect the
fixture’s ground wire to it. Otherwise, connect the fixture’s
ground wire directly to the mounting plate (A) using the
E
green screw provided.
8. Tuck wire connectors neatly into the junction box.
H
FINISHING THE INSTALLATION (Fig.1)
9. Place canopy (C) over mounting plate (A) and secure with
screws (D).
10. Place candle covers (K) over sockets (J).
11. Place cloth shade (L) onto candle cover (K). Adjust cloth
shadeLif necessary.
12. Install (3) three candelabra base bulbs (M) up to 60 watts
each or CFL or LED equivalent (not included) in
accordance with the fixture specification–DO NOT EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS
DEPASSER LA PUISSANCE NOMINALE MAXIMALE!)
Candle cover# CCV24075P-695
Rod# W30-1-695*1(F1) W30-1-695*2(F2) W30-H-695*1(F3) G
M
L
K I J
Your installation is now complete. Return power to the Fig. 2
junction box and test the fixture. Note: Illustration (Fig.1) on this manual is for installation
FIXTURE WIRES Black or Smooth
purposes only. It may or may not be identical to the
fixture purchased.
FIXTURE WIRES White or Ribbed HOUSE WIRES Black (Hot)
FIXTURE WIRES Bare Copper (Ground) HOUSE WIRES White (Neutral)
HOUSE WIRES Green (Ground)
Page:1/1
LA-3527E
