Minka Lavery 2785-695 Chelsea 5 Light Soft Brass Chandelier With White Silk Shades Instruction Manual

2785-695 Chelsea 5 Light Soft Brass Chandelier with White Silk Shades

Product Information

The product is a light fixture with item number 2785-695,
manufactured on January 20th, 2022. The fixture can be mounted on a
junction box and comes with a mounting plate, ground screw, and
mounting screws. The fixture has a rod assembly and three rods (F1,
F2, and F3) that can be threaded to adjust the hanging height. The
fixture supports five candelabra base bulbs up to 60 watts each or
their CFL/LED equivalent.

Product Usage Instructions

1. Turn off power at the fuse box or circuit breaker box.
2. Remove the old fixture, including the mounting hardware.
3. Unpack the new fixture and lay out all parts in a clean area.
   Ensure that no small parts are misplaced during installation.
4. Secure the rod (H) onto the all thread (I) on the fixture
   body.
5. Place the rod assembly (G) over all thread (E) on rod (H) and
   pass the wires through rod (H) during assembly.
6. Determine the desired hanging height and thread rods (F1, F2,
   and F3) to the all thread (E) of rod (H). Attach canopy (C) by
   threading onto rod (F1). Carefully feed wires through each rod as
   you assemble. Remove all thread if installing with one 6-rod
   only.
7. Attach mounting plate (A) to the junction box with mounting
   screws (B). The side of the mounting plate (A) marked GND and two
   convex points must face out.
8. Connect the electrical wires as shown in fig 2, making sure
   that all wire connectors are secured. Connect the fixture’s ground
   wire to the junction box’s ground wire or directly to the mounting
   plate (A) using the green screw provided.
9. Tuck wire connectors neatly into the junction box.
10. Place canopy (C) over mounting plate (A) and secure with screws
    (D).
11. Place candle covers (K) over sockets (J).
12. Place cloth shade (L) onto candle cover (K) and adjust if
    necessary.
13. Install five candelabra base bulbs (M) up to 60 watts each or
    their CFL/LED equivalent, in accordance with the fixture
    specification. DO NOT EXCEED THE MAXIMUM WATTAGE RATING.
14. Turn on power at the junction box and test the fixture.

INSTALLATION INSTRUCTIONS

Item#2785-695 (New. 2022/01/20) READ AND SAVE THESE INSTRUCTIONS
W AR NI N G ! S HU T P O WE R O F F AT F U S E O R CI R C UI T B R E AK E R .

AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.

MOUNTING THE FIXTURE (Fig.1)

Fig. 1

1. Shut off power at the fuse box or circuit breaker box and Set# A-021-118DH

remove the old fixture including the mounting hardware.

-Mounting plate

2. Carefully unpack your new fixture and lay out all the parts -Ground screw

A

in a clean area. Take care not to misplace any small parts -Mounting screws*2 B

necessary for installation.

C

3. Secure rod (H) onto all thread (I) on fixture body.

4. Place rod assembly (G) over all thread (E) on rod (H).

D

Carefully pass the wires through rod (H) during assembly.

F1

5. Determine the desired hanging height and thread rods (F1,

F2 and F3) to the all thread (E) of rod (H). Attach canopy

(C) by threading onto rod (F1). Carefully feed wires through

each rod as you assemble. Note: Remove all thread, if

F2

installing with one 6″ rod only.

F3

6. Attach mounting plate (A) to junction box (Not included)

with mounting screws (B) (Size: #8-32N*L0.5″). The side of

the mounting plate (A) marked “GND” and two convex

points must face out.

CONNECTING THE WIRES (Fig. 2)

7. Connect the electrical wires as shown in fig 2, making sure

that all wire connectors are secured. If your junction box

has a ground wire (green or bare copper), connect the

fixture’s ground wire to it. Otherwise, connect the fixture’s

E

ground wire directly to the mounting plate (A) using the

green screw provided.

H

8. Tuck wire connectors neatly into the junction box.

FINISHING THE INSTALLATION (Fig.1)

9. Place canopy (C) over mounting plate (A) and secure with

screws (D).

10. Place candle covers (K) over sockets (J).

11. Place cloth shade (L) onto candle cover (K). Adjust cloth

shadeLif necessary.

12. Install (5) five candelabra base bulbs (M) up to 60 watts

each or CFL or LED equivalent (not included) in

accordance with the fixture specification–DO NOT

EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS

DEPASSER LA PUISSANCE NOMINALE MAXIMALE!)

Candle cover# CCV24075P-695

Rod# W30-1-695*1(F1) W30-1-695*2(F2) W30-H-695*1(F3) G
M
L

I

K

J

Your installation is now complete. Return power to the Fig. 2

junction box and test the fixture.

FIXTURE WIRES Black or Smooth

Note: Illustration (Fig.1) on this manual is for installation purposes only. It may or may not be identical to the fixture purchased.

FIXTURE WIRES White or Ribbed HOUSE WIRES Black (Hot)

FIXTURE WIRES Bare Copper (Ground) HOUSE WIRES White (Neutral)

HOUSE WIRES Green (Ground)

Page:1/1

LA-3525E