Minka Lavery 2896-691 Pullman Junction 6-light Brushed Nickel And Coal Island Chandelier With Clear Glass Shades Instruction Manual

2896-691 Pullman Junction 6-Light Brushed Nickel and Coal Island Chandelier with Clear Glass Shades

Product Information

The product is a lighting fixture with item number 2896-691,
manufactured on August 18, 2021. The fixture requires six
candelabra base bulbs with a maximum wattage of 60 watts each, or
CFL or LED equivalent bulbs.

Product Usage Instructions

Before installation, shut off power at the fuse box or circuit
breaker box to ensure safety. Follow the steps below for proper
installation:

1. Remove the old fixture and mounting hardware.
2. Unpack the new fixture and lay out all parts in a clean area,
   taking care not to misplace any small parts.
3. Determine the desired hanging height and thread rods (F1, F2,
   F3) to all thread (J) on top of fixture body. Attach canopy (D) by
   threading onto rod (F1). Feed wires through each rod as you
   assemble. If installing with one 6 rod only, remove all
   thread.
4. Attach mounting plate (A) to the junction box with mounting
   screws (B). The side of the mounting plate (A) marked GND and two
   convex points must face out.
5. Use the support cable provided to support weight of fixture
   while wiring. Align the fixture to mounting plate (A) and attach
   hook (P) on the end of support cable (C) to a slot located on
   mounting plate (A). Allow the support cable (C) to support weight
   of the fixture while wiring.
6. Connect the electrical wires as shown in Fig. 2, making sure
   that all wire connectors are secured. If your junction box has a
   ground wire (green or bare copper), connect the fixture’s ground
   wire to it. Otherwise, connect the fixture’s ground wire directly
   to the mounting plate (A) using the green screw provided. Tuck wire
   connectors neatly into the junction box.
7. Slide canopy (D) over mounting plate (A) and secure with screws
   (E).
8. Install (6) six candelabra base bulbs up to 60 watts each or
   CFL or LED equivalent in accordance with the fixture specification.
   Do not exceed the maximum wattage rating.
9. Screw glass shades (I) onto socket cups (G).
10. Turn power back on at the junction box and test the
    fixture.

Note: The illustration provided in Fig. 1 is for installation
purposes only. It may or may not be identical to the fixture
purchased.

INSTALLATION INSTRUCTIONS

Item#2896-691 (New. 2021/08/18) READ AND SAVE THESE INSTRUCTIONS
W AR NI N G ! S HU T P O WE R O F F AT F U S E O R CI R C UI T B R E AK E R .

AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.

MOUNTING THE FIXTURE (Fig.1)

Fig. 1

1. Shut off power at the fuse box or circuit breaker box and Set# A-021-118DH

remove the old fixture including the mounting hardware.

-Mounting plate

2. Carefully unpack your new fixture and lay out all the parts -Ground screw in a clean area. Take care not to misplace any small parts -Mounting screws*2

necessary for installation.

3. Determine the desired hanging height and thread rods (F1,

F2 and F3) to all thread (J) on top of fixture body. Attach

canopy (D) by threading onto rod (F1). Carefully feed wires

through each rod as you assemble. Note: Remove all

thread, if installing with one 6″ rod only.

4. Attach mounting plate (A) to the junction box (Not included)

with mounting screws (B) (Size: #8-32N*L0.5″). The side of

the mounting plate (A) marked “GND” and two convex

F1

points must face out.

5. The support cable is provided to support weight of fixture

while wiring. Align the fixture to mounting plate (A) and

F2

attach hook (P) on the end of support cable (C) to a slot

F3

located on mounting plate (A). Carefully allow the support

J

cable (C) to support weight of the fixture while wiring.

CONNECTING THE WIRES (Fig. 2)

6. Connect the electrical wires as shown in fig 2, making sure

that all wire connectors are secured. If your junction box

has a ground wire (green or bare copper), connect the

fixture’s ground wire to it. Otherwise, connect the fixture’s

ground wire directly to the mounting plate (A) using the

green screw provided.

7. Tuck wire connectors neatly into the junction box.

COMPLETING THE INSTALLATION (Fig. 1)

8. Slide canopy (D) over mounting plate (A) and secure with

screws (E).

9. Install (6) six candelabra base bulbs (H) up to 60 watts

each or CFL or LED equivalent (not included) in

accordance with the fixture specification–DO NOT

EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS

DEPASSER LA PUISSANCE NOMINALE MAXIMALE!).

10. Screw glass shades (I) onto socket cups (G).

P A B C D E
Rod# W30-1-84*1(F1) W30-1-84*2(F2) W30-H-84*1(F3)
G H
I

Your installation is now complete. Return power to the

junction box and test the fixture.

Fig. 2

FIXTURE

WIRES

Note: Illustration (Fig.1) on this manual is for installation

Black or Smooth

purposes only. It may or may not be identical to the

fixture purchased.

FIXTURE WIRES White or Ribbed HOUSE WIRES Black (Hot)

FIXTURE WIRES Bare Copper (Ground) HOUSE WIRES White (Neutral)

HOUSE WIRES Green (Ground)

Page:1/1

LA-3462E