Minka Lavery 5496-729 Majestic Splendor 6 Light Sand Coal And Polished Nickel Cage Chandelier Instruction Manual

5496-729 Majestic Splendor 6 Light Sand Coal and Polished Nickel Cage Chandelier

Product Information:

The product is a fixture with item number 5496-729, designed for
indoor use. It requires a power source and comes equipped with a
crossbar, mounting screws, ground screw, rods, acrylic disks, and
candelabra base bulbs. The fixture can hold up to six 60-watt
candelabra base bulbs or CFL or LED equivalent bulbs. The
installation manual provides detailed instructions on how to
assemble and install the fixture.

Product Usage Instructions:

1. Before starting the installation process, shut off power at the
   fuse box or circuit breaker box and remove the old fixture
   including the mounting hardware.
2. Unpack the new fixture carefully and lay out all the parts in a
   clean area. Take care not to misplace any small parts necessary for
   installation.
3. Secure the stem onto all thread on fixture body.
4. Determine the desired hanging height and thread rods to all
   thread on stem. Screw loop onto rod J1. Carefully feed wire through
   each rod as you assemble.
5. Thread all thread into canopy loop and secure with lock washer
   and hex nut.
6. Thread the other end of all thread into crossbar and secure
   with lock washer and hex nut. Note: The length of the all thread
   into the crossbar may be adjusted if necessary.
7. Attach crossbar to the junction box with mounting screws. The
   side of the mounting plate marked GND and two convex points must
   face out.
8. Attach quick link to loop. Slide lock collar, acrylic disk, and
   canopy over quick link, then attach quick link to canopy loop.
   Carefully feed wire through loop, quick link, lock collar, acrylic
   disk, canopy, canopy loop, and all thread.
9. Connect the electrical wires as shown in the diagram, making
   sure that all wire connectors are secured. If your junction box has
   a ground wire (green or bare copper), connect the fixture’s ground
   wire to it. Otherwise, connect the fixture’s ground wire directly
   to the crossbar using the green screw provided.
10. Tuck wire connectors neatly into the junction box.
11. Raise the canopy and acrylic disk to the ceiling and secure
    with lock collar. Note: Adjust the canopy to be centered if
    necessary.
12. Install six candelabra base bulbs up to 60 watts each or CFL or
    LED equivalent in accordance with the fixture specification. DO NOT
    EXCEED THE MAXIMUM WATTAGE RATING!
13. Once installation is complete, return power to the junction box
    and test the fixture.

Note: It is important that the fixture is installed by a
qualified electrician to ensure proper wiring and installation.

INSTALLATION INSTRUCTIONS

Item#5496-729 (NEW. 05/24/2022) READ AND SAVE THESE INSTRUCTIONS
W AR NI N G ! SHUT P O WE R O FF AT F US E O R CI RC UI T BRE AKE R.

AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.

ASSEMBLING THE FIXTURE (Fig.1) 1. Shut off power at the fuse box or circuit breaker box and remove
the old fixture including the mounting hardware.
2. Carefully unpack your new fixture and lay out all the parts in a
clean area. Take care not to misplace any small parts necessary for installation.
3. Secure stem (L) onto all thread (M) on fixture body (O). 4. Determine the desired hanging height and thread rods (J1, J2, J3
and (Kto all thread on stem (L). Screw loop (I) onto rod (J1). Carefully feed wire through each rod as you assemble.
5. Thread all thread (C) into canopy loop (F). Secure with lock
washer (Y2) and hex nut (Y1).
6. Thread the other end of all thread (C) into crossbar (A). Secure
with lock washer (Y2) and hex nut (Y1). Note: The length of the
all thread into the crossbar may be adjusted if necessary.
7. Attach crossbar (A) to the junction box (not included) with
mounting screws (B) (Size: #8-32N*L1″). The side of the
mounting plate (A) marked “GND” and two convex points must
face out.
8. Attached quick link (H) to loop (I). Slide lock collar (G), acrylic
disk (E) and canopy (D) over quick link (H), then attach quick link
(H) to canopy loop (F). Carefully feed wire through loop (I), quick
link (H), lock collar (G), acrylic disk (E), canopy (D), canopy loop
(F) and all thread (C). CONNECTING THE WIRES (Fig. 2)
9. Connect the electrical wires as shown in fig 2, making sure that
all wire connectors are secured. If your junction box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the crossbar (A) using the green screw provided.
10. Tuck wire connectors neatly into the junction box. COMPLETING THE INSTALLATION (Fig. 1) 11. Raise the canopy (D) and acrylic disk (E) to the ceiling and
secure with lock collar (G). Note: Adjust the canopy to be centered if necessary.
12. Install (6) six candelabra base bulbs (N) up to 60 watts each or
CFL or LED equivalent (not included) in accordance with the fixture specification. –DO NOT EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!)

Fig.1

Set#A-010 -Crossbar -Ground screw -Mounting screw*2
Rod# -W39-3H-66*1(K) -W39-3-66*3(J1&J2&J3)
Acrylic # -GP5490-1*1 -GP5496*18

Your installation is now complete. Return power to the
junction box and test the fixture.
Note: Illustration (Fig. 1) on this manual is for installation purposes only. It may or may not be identical to the fixture purchased.

IMPORTANT: FIXTURE SHOULD BE INSTALLED BY A QUALIFIED ELECTRICIAN TO ENSURE PROPER WIRING AND INSTALLATION.

Fig. 2

Page: 1/1

LA-3473E