P5388-613 8-Light Charming Polished Nickel Island Chandelier
Product Information
The product is a light fixture with item number P5388-613. It
comes with a mounting plate, ground screw, mounting screws, candle
covers, glass, wire connectors, flat washers, lock washers, hex
nuts, and a wrench. The fixture has two arms (C1 and C2) with all
threads (K1 and K2) on top of the fixture. The fixture has a canopy
(I) that slides over the arms and is secured with flat washers,
lock washers, and hex nuts. The fixture requires eight candelabra
base bulbs (M) up to 60 watts each or CFL or LED equivalent (not
included). The installation of the fixture requires shutting off
power at the fuse box or circuit breaker box.
Product Usage Instructions
- Shut off power at the fuse box or circuit breaker box and
remove the old fixture including the mounting hardware. - Carefully unpack your new fixture and lay out all the parts in
a clean area. Take care not to misplace any small parts necessary
for installation. - Secure the bottom of arm (C1) to all thread (K1) on top of
fixture with coupler (L1); Secure the bottom of arm (C2) to all
thread (K2) with coupler (L2). - Slide canopy (I) over the all threads on arms (C1) and (C2),
then follow up with flat washers (N), lock washers (F), and secure
with hex nuts (G) using wrench (Z) provided. Carefully feed wire
through each part as you assemble. - Attach mounting plate (A) to the junction box (not included)
using the junction box screws (H). The side of mounting plate (A)
marked GND must face out. - Connect the electrical wires as shown in (Fig.2), making sure
that all wire connectors are secured. If your junction box has a
ground wire (green or bare copper), connect the fixture’s ground
wire to it. Otherwise, connect the fixture’s ground wire directly
to circular strap (A) using the ground screw provided. - Tuck the wire connectors neatly into the junction box.
- Slide canopy (I) over mounting plate (A) and secure with screws
(H). - Install eight candelabra base bulbs (M) up to 60 watts each or
CFL or LED equivalent (not included) in accordance with the fixture
specification–DO NOT EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS
DEPASSER LA PUISSANCE NOMINALE MAXIMALE!) - Alternate glass (O) and (Q) on hooks (Q), then hang hooks (J)
to each glass (O) and (Q). Alternate again glass (Q) and (O) on
hooks (P). Your installation is now complete. Return power to the
junction box and test the fixture.
INSTALLATION INSTRUCTIONS
Item#P5388-613 (New. 05/13/2022) READ AND SAVE THESE INSTRUCTIONS
W AR NI N G ! S HU T P O WE R O F F AT F U S E O R CI R C UI T B R E AK E R .
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
PREPARATION (Fig. 1)
1. Shut off power at the fuse box or circuit breaker box an
remove the old fixture including the mounting hardware.
2. Carefully unpack your new fixture and lay out all the parts in a
clean area. Take care not to misplace any small parts necessary for installation.
ASSEMBLING THE FIXTURE (Fig.1) 3. Secure the bottom of arm (C1) to all thread (K1) on top of
fixture with coupler (L1); Secure the bottom of arm (C2) to all
thread (K2) with coupler (L2).
4. Slide canopy (I) over the all threads on arms (C1) and (C2),
then follow up with flat washers (N), lock washers (F), and
secure with hex nuts (G) using wrench (Z) provided. Carefully
Fig.1
Set#A-020-160117 -mounting plate -Ground Screw -Mounting Screws*4
# CCV21085P-613
-Candle covers*8 E
Glass#
G
PG5381-1*40(O) PG5381-2*40(Q) F
ZN
feeding wire through each part as you assemble.
5. Attach mounting plate (A) to the junction box (not included)
using the junction box screws (H). The side of mounting plate
(A) marked “GND” must face out.
C2
CONNECTING THE WIRES (Fig. 2)
6. Connect the electrical wires as shown in (Fig.2), making sure
that all wire connectors are secured. If your junction box has a ground wire (green or bare copper), connect the fixture’s ground
L2
K2
wire to it. Otherwise, connect the fixture’s ground wire directly to
L
circular strap (A) using the ground screw provided.
7. Tuck the wire connectors neatly into the junction box.
COMPLETING THE INSTALLATION (Fig. 1)
8. Slide canopy (I) over mounting plate (A) and secure with screws
(H).
9. Install (8) eight candelabra base bulbs (M) up to 60 watts each
M
or CFL or LED equivalent (not included) in accordance with the
fixture specification–DO NOT EXCEED THE MAXIMUM
WATTAGE RATING! (NE PAS DEPASSER LA PUISSANCE
NOMINALE MAXIMALE!)
10. Alternate glass (O) and (Q) on hooks (Q), then hang hooks (J)
to each glass (O) and (Q). Alternate again glass (Q) and (O) on Fig. 2
hooks (P). Your installation is now complete. Return power to the junction box
FIXTURE WIRES Black or Smooth
FIXTURE WIRES White or Ribbed
and test the fixture.
Note: Illustration (Fig. 1) on this manual is f installation purposes only. It may or may not be identical to the fixture purchased.
HOUSE WIRES Black (Hot)
R
A B G F N H I
C1
L1 K1
J
O
P Q
FIXTURE WIRES Bare Copper (Ground)
HOUSE WIRES White (Neutral)
HOUSE WIRES Green (Ground)
Page: 1/2
Fig.3
E G F N Z
a. Hardware Bag:
A. Mounting plate *1
I. Canopy *1
R. Wire connectors *3
H. Mounting Screws*4
E. Ground screw *1
B. Screws *2
N. Flat washers *2 F. Lock washers *2
A
G. Hex nut *2
Z. Wrench *1
Pa
2/3 Page: 2/2
R
A B G F N H I
I
R HEB N F G Z
