P1360-619 Nexpo 10-Light Island Chandelier
Product Information
The product is a hanging fixture with item number P1360-619/66A.
It comes with a metal support plate, canopy, glass shade, and ten
candelabra base bulbs (not included). The fixture has three rods
(F1, F2, and F3) that can be threaded to adjust the hanging height.
The installation requires drywall anchors, mounting screws, and
wood screws. The fixture has black or smooth wires for hot
connection, white or ribbed wires for neutral connection, and bare
copper wires for ground connection. The product is rated for a
maximum wattage of 60 watts per bulb.
Product Usage Instructions
- Unpack the fixture and ensure that all parts are included.
- Turn off power at the circuit breaker and remove the old
fixture including the mounting hardware. - Thread rods (F1, F2, and F3) to all thread (J) on the fixture
body. Pass the wires through each rod during assembly and secure
swivels (G) onto rods (F1). - Align canopy (H), metal support plate (I), lock washer (L), and
metal washer (E) onto swivels (G) and secure with hex nuts (D) via
wrench (J). - Position mounting plate (A) on the ceiling and mark the
location of the two drywall anchors (K). Pre-drill the holes for
the drywall anchors (K). Insert the drywall anchors (K) into the
ceiling and attach mounting plate (A) to the junction box using
mounting screws (B) and wood screws (O) into drywall anchors (K).
The side of the mounting plate marked GND must face out. - Connect the electrical wires as shown in Fig. 2, making sure
that all wire connectors are secured. If your junction box has a
ground wire (green or bare copper), connect the fixture’s ground
wire to it. Otherwise, connect the fixture’s ground wire directly
to mounting plate (A) using the green screw provided. After wires
are connected, tuck them carefully inside the junction box. - Align canopy (H) over mounting plate (A) and secure with screws
(C). - Place glass shade (M) over socket (L) and secure with screw
shell (N). - Install ten candelabra base bulbs (Q) up to 60 watts each or
CFL or LED equivalent (not included) in accordance with the fixture
specification. Do not exceed the maximum wattage rating. - The dendrites of this lamp have the function of rotating a
certain angle so that customers can make their own
adjustments. - Turn on power at the circuit breaker and test the fixture.
Note: The illustration in Fig. 1 is for installation purposes
only and may or may not be identical to the purchased fixture. The
fixture should be installed by a qualified electrician to ensure
proper wiring and installation.
INSTALLATION INSTRUCTIONS
Item#P1360-619/66A (New. 2022/06/15) READ AND SAVE THESE INSTRUCTIONS
W AR NI NG ! S HUT POWE R O F F AT F US E O R CI RC UI T BR E AKE R.
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
HANGING THE FIXTURE (Fig. 1)
Fig.1
1. Carefully remove the fixture from the carton and check that all
parts are included as shown in the illustration.
Set# A-021-220118
2. Shut off power at the circuit breaker and remove the old fixture -Mounting Plate
including the mounting hardware. 3. Determine the desired hanging height and thread rods (F1, F2
-Ground Screw -Mounting Screw*2
K
and F3) to all thread (J) on the fixture body. Carefully pass the
O
wires through each rod during assembly. Secure swivels (G)
D
onto rods (F1).
E L
4. Align canopy (H), metal support plate (I) followed by lock
I
washer (L) and metal washer (E) onto swivels (G) and secure
with hex nuts (D) via wrench (J) (not included).
5. Position mounting plate (A) on the ceiling and mark the location
of the two drywall anchors (K). Pre-drill the holes for the drywall
anchors (K). Then insert the drywall anchors (K) into the ceiling.
6. Attach mounting plate (A) to the junction box (not included)
using mounting screws (B) (Size: #8-32N*L0.5″) and wood
screws (O) into drywall anchors (K). The side of the mounting
plate marked “GND” must face out.
CONNECTING THE WIRES (Fig. 2)
7. Connect the electrical wires as shown in Fig. 2, making sure
that all wire connectors are secured. If your junction box has a
ground wire (green or bare copper), connect the fixture’s ground
wire to it. Otherwise, connect the fixture’s ground wire directly to
mounting plate (A) using the green screw provided. After wires
are connected, tuck them carefully inside the junction box.
COMPLETING THE INSTALLATION (Fig. 1) 8. Align canopy (H) over mounting plate (A) and secure with
J
screws (C).
9. Place glass shade (M) over socket (L) and secure with screw
shell (N).
10. Install (10) ten candelabra base bulbs (Q) up to 60 watts each
or CFL or LED equivalent (not included) in accordance with the
fixture specification. –DO NOT EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!). 11. The dendrites of this lamp have the function of rotating a certain
Rod# W30-1-84/66A*2(F1) W30-1-84/66A *4(F2) W30-H-84/66A *2(F3)
angle so that customers can make their own adjustments.
Fig. 2
Your installation is now complete. Return power to the junction box and test the fixture. Note: Illustration (Fig. 1) on this manual is for installation purposes only. It may or may not be identical to the fixture purchased.
FIXTURE WIRES Black or Smooth
FIXTURE WIRES White or Ribbed HOUSE WIRES Black (Hot)
IMPORTANT: FIXTURE SHOULD BE INSTALLED BY A QUALIFIED ELECTRICIAN TO ENSURE PROPER WIRING AND INSTALLATION.
A B J C H G F1
F2
F3
L M N Q
FIXTURE WIRES Bare Copper (Ground)
HOUSE WIRES White (Neutral)
HOUSE WIRES Green (Ground)
LA-2884E
