George Kovacs P8155-681 Cosmet 6-light Black And Aged Brass Chandelier Instruction Manual

P8155-681 Cosmet 6-Light Black and Aged Brass Chandelier

Product Information: Installation Instructions for
P8155-681

The P8155-681 is a light fixture that requires installation. It
comes with a mounting plate, canopy, front plate, rods, fixture
body, light arms, socket cup, glass shade, and screws for
installation. The fixture requires a 6*40W Xenon bulb or LED
equivalent.

Warning:

Before installing the fixture, ensure that the power is shut off
at the fuse or circuit breaker.

Preparing for Installation:

1. Shut off power at the fuse box or circuit breaker box and
   remove the old fixture including the mounting hardware.
2. Carefully unpack your new fixture and lay out all the parts in
   a clear area. Take care not to misplace any small parts necessary
   for installation.

Suggested Installation:

1. Remove the two mounting screws (E) from the side of the canopy
   (D) and remove the mounting plate (B).
2. Attach the mounting plate (B) to the junction box (not
   included) with the two outlet box screws (C) provided.
3. One 6 rod and one 12 rod were assembled on the fixture already,
   if not using additional rods, skip to step 9.
4. Loose the wire nuts for the fixture wires inside the canopy.
   Put the short black and white wire aside. Loosen the hex nuts and
   lock washers to take the canopy (D) and front plate off from the
   rods (F2).
5. Thread the fixture wires up through the rods (F1) & (F2),
   then tighten to the fixture body (G). Determine the desired length
   of the fixture, adding the other rod (F1) or (F2) as needed.
6. Thread the fixture wires from the front plate up through the
   canopy (D), then secure with the lock washers and hex nuts. Cut
   excess wire leaving 7 for installation.

Connecting the Wires:

7. Connect the electrical wires as shown in Fig. 2, making sure
   that all wire connectors are secured. If your outlet has a ground
   wire (green or bare copper), connect the fixture’s ground wire to
   it. Otherwise, connect the fixture’s ground wire directly to the
   mounting plate (B) using the green screw provided. Tuck the wire
   connections neatly into the junction box.

Completing the Installation:

1. Attach the canopy (D) to the mounting plate (B) and secure it
   with the mounting screws (E).
2. Install the 6*40W Xenon bulb (I) (included) or LED equivalent
   in accordance with the fixture’s specifications. (DO NOT EXCEED THE
   MAXIMUM WATTAGE RATING!).
3. Place glass shade (J) over the socket and twist to secure it to
   the socket cup (H). Don’t over tighten.
4. Adjust each light arm (K) to the desired position.

Your installation is now complete. Return power to the junction
box and test the fixture.

INSTALLATION INSTRUCTIONS FOR P8155-681
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
AVERTISSEMENT ! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DO DISJO NCTEUR

PREPARING FOR INSTALLATION (Fig. 1) 1. Shut off power at the fuse box or circuit breaker box and
remove the old fixture including the mounting hardware. 2. Carefully unpack your new fixture and lay out all the parts in
a clear area. Take care not to misplace any small parts necessary for installation.

Fig.1

SUGGESTED INSTALLATION (Fig. 1 and Fig. 2) 3. Remove the two mounting screws (E) from the side of the
canopy (D) and remove the mounting plate (B). 4. Attach the mounting plate (B) to the junction box (not
included) with the two outlet box screws (C) provided. 5. One 6″ rod and one 12″ rod were assembled on the fixture
already, if not using additional rods, skip to step 9. 6. Loose the wire nuts for the fixture wires inside the canopy.
Put the short black and white wire aside. Loosen the hex nuts and lock washers to take the canopy (D) and front plate off from the rods (F2). 7. Thread the fixture wires up through the rods (F1) & (F2), then tighten to the fixture body (G). Determine the desired length of the fixture, adding the other rod (F1) or (F2) as needed. 8. Thread the fixture wires from the front plate up through the canopy (D), then secure with the lock washers and hex nuts. Cut excess wire leaving 7″ for installation.

CONNECTING THE WIRES (Fig. 2) 9. Connect the electrical wires as shown in Fig. 2, making sure
that all wire connectors are secured. If your outlet has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting plate (B) using the green screw provided. Tuck the wire connections neatly into the junction box.

COMPLETING THE INSTALLATION (Fig. 1) 10. Attach the canopy (D) to the mounting plate (B) and secure
it with the mounting screws (E). 11. Install the 6*40W Xenon bulb (I) (included) or LED
equivalent in accordance with the fixture’s specifications. (DO NOT EXCEED THE MAXIMUM WATTAGE RATING!). 12. Place glass shade (J) over the socket and twist to secure it to the socket cup (H). Don’t over tighten. 13. Adjust each light arm (K) to the desired position.
Your installation is now complete. Return power to the
junction box and test the fixture.

Fig. 2
FIXTURE WIRES Black or Smooth

set# A-021-114D – Mounting plate – Ground screw – Mounting screws*2pcs

FIXTURE WIRES White or Ribbed

FIXTURE WIRES Bare Copper (Ground)

Page: 1/1

HOUSE WIRES Black (Hot)

HOUSE WIRES White (Neutral)

HOUSE WIRES Green (Ground)