Metropolitan N7819-726 Soho 6-light Coal And Soft Brass Island Chandelier Instruction Manual

N7819-726 Soho 6-Light Coal and Soft Brass Island Chandelier

Product Information

The product is an indoor ceiling light fixture, with item number
N7819-726, manufactured on May 11, 2022. The fixture requires six
candelabra base bulbs up to 60 watts each or CFL or LED equivalent
(not included). The fixture has a maximum wattage rating that
should not be exceeded.

Product Usage Instructions

1. Before installation, shut off power at the fuse box or circuit
   breaker box.
2. Remove the old fixture including the mounting hardware.
3. Carefully unpack your new fixture and lay out all the parts in
   a dry and safe place.
4. Use drywall anchors (K) to pre-drill holes into the ceiling.
   Then, insert drywall anchors (K) into the ceiling.
5. Attach the mounting plate (A) to the junction box (not
   included) with the mounting screw.
6. Connect the fixture wires to the house wires:
   • Connect the black or smooth fixture wire to the black (hot)
     house wire.
   • Connect the white or ribbed fixture wire to the white (neutral)
     house wire.
   • Connect the bare copper fixture wire to the green (ground)
     house wire.
7. Align the canopy (H) onto the mounting plate (A) and secure
   with screws (C).
8. Place the glass panel (M) into the metal frame (T) and secure
   with tabs provided.
9. Install six candelabra base bulbs (Q) up to 60 watts each or
   CFL or LED equivalent (not included) in accordance with the fixture
   specification. DO NOT EXCEED THE MAXIMUM WATTAGE RATING!
10. After completing the installation, turn the power back on at
    the junction box and test the fixture.

INSTALLATION INSTRUCTIONS

Item#N7819-726 (New. 2022/05/11) READ AND SAVE THESE INSTRUCTIONS
W AR NI N G ! S HU T P O WE R O F F AT F U S E O R CI R C UI T B R E AK E R .

AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.

PREPARATION (Fig. 1) 1. Shut off power at the fuse box or circuit breaker box and
remove the old fixture including the mounting hardware. 2. Carefully unpack your new fixture and lay out all the parts in a
clean area. Take care not to misplace any small parts necessary for installation. ASSEMBLING THE FIXTURE (Fig. 1) 3. Loosen hex nuts (D), take apart metal washer (E), lock washer (L), and swivel (G). 4. Determine the desired hanging height and thread rods (F1, F2 and F3) to all thread (S) on fixture body. Carefully pass wires through each rod during assembly. Secure swivels (G) onto rods (F1). 5. Align canopy (H) and metal plate (I) followed by lock washer (L) and metal washer (E) onto swivels (G) and secure with hex nuts (D) via Wrench (J) (not included). 6. Position mounting plate (A) on ceiling and mark location of the two
drywall anchors (K). Pre-drill holes for drywall anchors (K). Then
insert drywall anchors (K) into ceiling. 7. Attach mounting plate (A) to junction box (Not included) with
mounting screws (B) (Size: #8-32N*L0.5″) and wood screws (O) into drywall anchors (K). The side of the mounting plate marked “GND” must face out. 8. The support cable is provided to support weight of fixture while wiring. Align fixture to mounting plate (A) and attach hook (P) on end of support cable (R) into a slot located on mounting plate (A). Carefully allow support cable (R) to support the weight of fixture while wiring. CONNECTING THE WIRES (Fig. 2) 9. Connect the electrical wires as shown in Fig. 2, making sure that all wire connectors are secured. If your junction box has a ground wire (green or bare copper), connect fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting plate (A) using green screw provided. 10. Tuck wire connectors neatly inside the junction box.
COMPLETING THE INSTALLATION (Fig. 1) 11. Align canopy (H) onto mounting plate (A) and secure with screws (C). 12. Place glass panel (M) into metal frame (T) and secure with tabs
provided. 13.Install (6) six candelabra base bulbs (Q) up to 60 watts each or CFL
or LED equivalent (not included) in accordance with the fixture specification. –DO NOT EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!).
Your installation is now complete. Return power to the junction box and test the fixture.

Fig. 1

Set# A-021-246120

-Mounting plate

-Ground screw

K

-Mounting screw *2 O D E L I

R

Rod# W30-1-66A *2 (F1)
W30-1-66A *4 (F2) W30-H-66A *2 (F3)

Fig. 2
FIXTURE WIRES Black or Smooth

FIXTURE WIRES White or Ribbed

A B J
C H G F1 F2
F3 S
Q
FIXTURE WIRES Bare Copper (Ground)

Note: Illustration (Fig. 1) on this manual is for installation purposes only. It may or may not be identical to the fixture purchased.

HOUSE WIRES Black (Hot)

HOUSE WIRES White (Neutral)

P
T M
HOUSE WIRES Green (Ground)

LA-3545E