Metropolitan N7359-790 Prima Vista 8-light Aged Antique Brass Island Chandelier With Clear Acrylic Accents Instruction Manual

N7359-790 Prima Vista 8-Light Aged Antique Brass Island Chandelier with Clear Acrylic Accents

Product Information

Product Name: Fixture Item#N7359-790

Date of Manufacture: 2022/5/20

Product Usage Instructions

1. Before starting the installation process, ensure that the power
   is shut off at the fuse or circuit breaker. This is important for
   safety.
2. Remove the old fixture, including the mounting hardware, from
   the fuse box or circuit breaker box.
3. Carefully unpack the new fixture and lay out all the parts in a
   clean area. Take care not to misplace any small parts necessary for
   installation.
4. Adjust the arms of the fixture to the proper position as shown
   in Fig. 4.
5. Thread the fixture loop (H) onto the all thread (J) of the
   upper assembly (K).
6. Secure the stems (M) to the all thread (O) of the socket
   assembly (S), and then thread the upper assembly (K) to the stem
   (M).
7. Place bolts (N) through holes on top of the frame assembly (R)
   and tighten them with plastic washers and finials (Q).
8. Thread the all thread (C) into the center lock hole of the
   crossbar (A) using a lock washer (Y1) and hex nut (Y2) until snug.
   Adjust the length of all thread (C) into the crossbar if
   necessary.
9. Mount the crossbar (A) assembly to the ceiling junction box
   using the provided mounting screws (B). Ensure that the side of
   crossbar (A) marked GND faces out.
10. Attach the quick link (F) to the fixture loop (H) and chain
    (G). Close the quick link completely when installed. Determine the
    correct number of links needed for the desired hanging height and
    use chain pliers to open one end link of the chain. Discard excess
    chain and attach the quick link (F) to the loop on the bottom of
    the canopy (D), then close the quick link (F). Lace the fixture
    wires through the chain links and pull until tight. Feed the wires
    through the canopy and all thread, then pull until tight.
11. Use the provided support cable (I) to support the weight of the
    fixture while wiring. Align the fixture to the crossbar (A) and
    attach the hook (T) on the end of the support cable (I) into a slot
    located on crossbar (A). Carefully allow the support cable (I) to
    support the weight of the fixture while wiring.
12. Connect the electrical wires as shown in Fig. 3, ensuring that
    all wire connectors are secured. If your junction box has a ground
    wire (green or bare copper), connect the fixture’s ground wire to
    it. Otherwise, connect the fixture’s ground wire directly to the
    crossbar using the provided green screw.
13. Tuck the wire connections neatly into the junction box.
14. Attach the canopy (D) over the end of the all thread (C) and
    secure it with the hex nut (Y2) until snug.
15. Thread the finial (E) onto the end of the all thread (C) and
    hand tighten it snugly.
16. Install up to 8 candelabra base bulbs (P) with a maximum
    wattage of 60 watts each, or CFL or LED equivalent bulbs, according
    to the fixture specification. Do not exceed the maximum wattage
    rating.
17. Once the installation is complete, return power to the junction
    box and test the fixture.

INSTALLATION INSTRUCTIONS FOR FIXTURE Item#N7359-790 (New. 2022/5/20)
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.

ASSEMBLING THE FIXTURE (FIG. 1 & Fig. 4)

Fig. 1

T

1. Shut off power at the fuse box or circuit breaker box and remove the old fixture including the mounting hardware.
2. Carefully unpack your new fixture and lay out all the parts in a clean area. Take care not to misplace any small parts necessary for installation.
3. The arms have been placed to lay flat for shipping. Adjust arms to proper

Set#A-012 – Crossbar – Ground Screw – Mounting Screw *2

position. (See Fig. 4)

4. Thread fixture loop (H) onto all thread (J) of upper assembly (K).

5. Secure stems (M) to all thread (O) of socket assembly (S). Then thread

upper assembly (K) to stem (M).

6. Carefully place bolts (N) through holes on top of frame assembly (R). Then

tighten with plastic washers and finials (Q).

Fig. 4

ASSEMBLING THE FIXTURE (FIG. 2) 7. Thread the all thread(C) into the center lock hole of the crossbar (A) with
lock washer (Y1) and hex nut (Y2) until snug. Note: The length of all thread (C) into crossbar may be adjusted if necessary. 8. Take crossbar (A) assembly and mount to ceiling junction box (Not included) using mounting screws (B) (Size: # 8-32N*L1″). The side of crossbar (A) marked “GND” must face out..
9. Attach quick link (F) to fixture loop (H) and chain (G). Quick link must be completely closed when installed. By measuring, determine correct number of links needed for desired hanging height. Use a pair of chain pliers to open one end link of chain and discard excess chain. Attach quick link (F) to the loop on bottom of canopy(D), then close quick link (F). Carefully lace fixture wires through chain links and pull until tight. Feed wires through canopy and all thread, then pull until tight.
10. The support cable is provided to support the weight of the fixture while wiring. Align the fixture to the crossbar(A) and attach hook(T) on the end of support cable(I) into a slot located on crossbar(A). Carefully allow the support cable(I) to support the weight of the fixture while wiring

Acrylic Pole# – GP7356-1*12 – GP7359*4
Fig. 2

CONNECTING THE WIRE (Fig. 3) 11. Connect the electrical wires as shown in Fig. 3, making sure that all wire
connectors are secured. If your junction box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to crossbar using the green screw provided.
12. Tuck wire connections neatly into junction box.

Chain# HCH2372-790

COMPLETING THE INSTALLATION (Fig. 1) 13. Attach the canopy(D) over the end of the all thread(C) and secure with the
hex nut(Y2) until snug. 14. Thread the finial(E) onto the end of the all thread(C) and hand tighten snug. 15. Install (8) eight candelabra base bulbs (P) up to 60 watts each or CFL or
LED equivalent (not included) in accordance with the fixture specification. — DO NOT EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!)

Your installation is now complete. Return power to the junction box and test the fixture.
Note: Illustration (Fig. 1) on this manual is for installation purposes only. It may or may not be identical to the fixture purchased.

Fig. 3

Notice: It is important to use proper chain pliers (not included) To OPEN and CLOSE the chain included with this fixture. Do not open them with other tools that may twist or stress the chain links. It is important to use proper chain pliers like the ones shown in the diagram.