Metropolitan N7811-726 Soho 1 Light Coal And Soft Brass Cage Mini Pendant Instruction Manual

N7811-726 Soho 1 Light Coal and Soft Brass Cage Mini Pendant

Product Information

The product is an indoor ceiling light fixture with a metal ring
and glass shade. The fixture requires one medium base bulb up to 60
watts each or CFL or LED equivalent (not included). The fixture
comes with a mounting plate, ground screw, mounting screws, and
all-thread rods. The product has a maximum wattage rating that
should not be exceeded.

Product Usage Instructions

1. Shut off power at the fuse box or circuit breaker box and
   remove old fixture including the mounting hardware.
2. Carefully unpack the new fixture and lay out all the parts in a
   clear area. Take care not to misplace any small parts necessary for
   installation.
3. Determine the desired hanging height and thread rods (F1, F2,
   and F3) to all thread (G) on the fixture body.
4. Attach the canopy (D) by threading onto rod (F1). Carefully
   pass wires through each rod during assembly. Note: Remove all
   thread if installing with one 6 rod only.
5. Attach the mounting plate (A) to the junction box (not
   included) with mounting screws (B). The side of mounting plate (A)
   marked GND and two convex points must face out.
6. Connect electrical wires as shown in Fig 2, making sure that
   all wire connectors are secured. If your junction box has a ground
   wire (green or bare copper), connect the fixture’s ground wire to
   it. Otherwise, connect the fixture’s ground wire directly to
   mounting plate (A) using the green screw provided. Tuck wire
   connectors neatly inside the junction box.
7. Place the canopy (D) over the mounting plate (A) and secure
   with screws (E).
8. Place the glass shade (J) into the metal ring (H) and secure
   the shade by adjusting each screw (I) on the metal mesh holder
   (C).
9. Install one medium base bulb (K) up to 60 watts each or CFL or
   LED equivalent (not included) in accordance with the fixture
   specification. DO NOT EXCEED THE MAXIMUM WATTAGE RATING!
10. Return power to the junction box and test the fixture.

INSTALLATION INSTRUCTIONS

Item#N7811-726 (New. 2022/05/05) READ AND SAVE THESE INSTRUCTIONS
W AR NI N G ! S HU T P O WE R O F F AT F U S E O R CI R C UI T B R E AK E R .

AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.

PREPARATION (Fig.1)

Fig. 1

1. Shut off power at the fuse box or circuit breaker box and remove old fixture including the mounting hardware.
2. Carefully unpack your new fixture and lay out all the parts
in a clear area. Take care not to misplace any small parts
necessary for installation.

Set#A-021-118DH -Mounting plate -Ground screw -Mounting screw *2
F1

A B D E

ASSEMBLING THE FIXTURE (Fig. 1) 3. Determine the desired hanging height and thread rods
(F1, F2 and F3) to all thread (G) on fixture body. Attach canopy (D) by threading onto rod (F1). Carefully pass wires through each rod during assembly. Note: Remove all thread, if installing with one 6″ rod only. 4. Attach mounting plate (A) to junction box (not included) with mounting screws (B) (Size: #8-32N*L0.5″). The side of mounting plate (A) marked “GND” and two convex points must face out.
CONNECTING THE WIRES (Fig. 2) 5. Connect electrical wires as shown in Fig 2, making sure
that all wire connectors are secured. If your junction box has a ground wire (green or bare copper), connect fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to mounting plate (A) using green screw provided. 6. Tuck wire connectors neatly inside the junction box.

F2

F3

Rod# W30-1-66A *1 (F1)

W30-1-66A *2 (F2)

G

W30-H-66A *1 (F3)

C

H I

COMPLETING THE INSTALLATION (Fig. 1) 7. Place canopy (D) over mounting plate (A) and secure
with screws (E). 8. Place glass shade (J) into metal ring (H) and secure
shade by adjusting each screw (I) on metal mesh holder (C). 9. Install (1) one medium base bulb (K) up to 60 watts each or CFL or LED equivalent (not included) in accordance with the fixture specification–DO NOT EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!).

J K

Your installation is now complete. Return power to the junction box and test fixture.
Note: Illustration (Fig. 1) on this manual is for installation purposes only. It may or may not be identical to the fixture purchased.

Fig. 2 FIXTURE WIRES Black or Smooth

FIXTURE WIRES White or Ribbed

FIXTURE WIRES Bare Copper (Ground)

HOUSE WIRES Black (Hot)

HOUSE WIRES White (Neutral)

HOUSE WIRES Green (Ground)

Page: 1/1

LA-3541E