2105-726 Townhall 4-Light Soft Brass and Coal Cage Pendant Light
Product Information
The product is Item#2105-726, a new fixture for installation. It
comes with a mounting plate, ground screw, junction box screw, rod,
candle cover, and acrylic ball. The fixture wires are black or
smooth, white or ribbed, and bare copper for ground. The house
wires are black for hot, white for neutral, and green for ground.
The installation manual also includes hardware bags A and B with
additional parts such as a canopy, mounting screw, lock-up knob,
quick link, and loop.
Product Usage Instructions
- Shut off power at the fuse box or circuit breaker box and
remove the old fixture including the mounting hardware. - Unpack the new fixture and lay out all the parts.
- Refer to Fig. 1 for the preparation steps which include
attaching the mounting plate, ground screw, and junction box
screw. - Refer to Fig. 2 for the fixture wires and house wires color
codes and connect them accordingly. - Refer to Fig. 3 for the additional hardware parts and attach
them as required. - Once all the parts are attached, turn on the power and test the
fixture.
Note: The illustration in Fig. 1 is for installation purposes
only and may or may not be identical to the fixture purchased.
INSTALLATION INSTRUCTIONS
Item#2105-726 (New.07/01/2022) READ AND SAVE THESE INSTRUCTIONS
W AR NI N G ! S HU T P O WE R O F F AT F U S E O R CI R C UI T B R E AK E R .
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
PREPARATION (Fig. 1) 1. Shut off power at the fuse box or circuit breaker box and
remove the old fixture including the mounting hardware. 2. Carefully unpack your new fixture and lay out all the parts
in a clean area. Take care not to misplace any small parts necessary for installation. ASSEMBLING THE FIXTURE WITH CHAIN LOOP (Fig.1&Fig. 3) 3. Place square tubes (L) on metal frame (N) and attach with countersunk screws (M) (Size: 8#-32N*L0.3″). 4. Align top frame (H) with square tubes (L) and attach with screws (T) (Size: 8#-32N*L0.3″) and cover the hole with plastic plug (S). 5. Screw metal tube (J) onto the all thread on light cluster (K). 6. Attach center rod (I) onto all thread on metal tube (J). 7. Thread center rod (I) into the all thread on top frame (H). 8. Place acrylic ball (Q) to bottom of fixture body (K) and secure with allen screw (O) using wrench (P) provided. 9. Determine the desired hanging height and thread rods (G1, G2) to the all thread of top frame (H). Then attach loop (F1) by screwing onto rod (G1). Pass the wires carefully through each rod as you assembled. 10. Attach quick link (E) connect to loop (F1) and loop (F2) on canopy (C), carefully feed the wire through loop (F1), quick link (E) and loop (F2). 11. Attach mounting plate (A) to the junction box (not included) with junction box screws (B) (Size: #8-32N*L1″). The side of the mounting plate (A) with “GND” marked on it and two convex points must face out. 12. The support cable is provided to support weight of fixture while wiring. Align fixture to mounting plate (A) and attach hook (W) on the end of support cable (V) into a slot located on mounting plate (A). Carefully allow support cable (V) to support weight of fixture while wiring (Fig.1 Fig3). CONNECTING THE WIRES (Fig. 2) 13. Connect the electrical wires as shown in fig.2, making sure that all wire connectors are secured. If junction box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting plate (A) using the green screw provided. 14. Tuck the wire connectors neatly into the junction box. COMPLETING THE INSTALLATION (Fig. 1) 15. Slide canopy (C) over mounting screws (U) attached to mounting plate (A) and secure with knobs (D). 16. Install (4) four candelabra base bulbs up to 60 watts each or CFL or LED equivalent (not included) in accordance with the fixture specification–DO NOT EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!)
Fig. 1 Set#A-020-A Mounting Plate x1pc Ground Screw x1pc Junction box Screw x2pcs
Rod# G1. W30-H-66A G2. W30-1-66A
Candle Cover# CCV20135P-695 Acrylic Ball# GP2105
Fig. 2
FIXTURE WIRES Black or Smooth
FIXTURE WIRES White or Ribbed
FIXTURE WIRES Bare Copper (Ground)
HOUSE WIRES Black (Hot)
HOUSE WIRES White (Neutral)
HOUSE WIRES Green (Ground)
Page 1/2
LA-3279E
Your installation is now complete. Return power to the junction box and test the fixture.
Note: Illustration (Fig. 1) on this manual is for installation purposes only. It may or may not be identical to the fixture purchased.
Fig.3
a. Hardware Bag A. Mounting Plate x 1pc B. Junction Box
Screw x 2pcs C. Canopy x 1pc U. Mounting Screw x 2pcs D. Lock-up Knob x 2pcs E. Quick Link x 1pcs F1. Loop x 2pcs b. Hardware Bag G1. Rod 6″ x1pc G2. Rod 12″ x3pcs
A B C D
E F1
G1
A
B
U V
F2
C
W
U
D
E
F1
G1
G2
Page 2/2
LA-3279E
