N7814-726 Soho 4-Light Coal and Soft Brass Cage Pendant
Product Information: Convertible Lamps for Pendant
The Item#N7814-726 Convertible Lamps for Pendant is a lighting
fixture that can be mounted on the ceiling and used as a pendant
light. The fixture comes with a metal frame, metal tube, mounting
plate, ground screw, mounting screws, all thread, canopy, glass
panel, and medium base bulbs. The fixture is designed to
accommodate up to four medium base bulbs with a maximum wattage of
60 watts each or CFL or LED equivalent.
Product Usage Instructions:
- Shut off power at the fuse box or circuit breaker box.
- Remove the old fixture including the mounting hardware.
- Unpack the new fixture and lay out all the parts in a clean
area. - Place the metal frame over the metal tube and secure with
screws. - Determine the desired hanging height and thread rods to all
thread on fixture body. - Attach the canopy by threading onto rod. Carefully feed wires
through each rod as you assemble. - Attach mounting plate to the junction box with mounting screws.
The side of mounting plate marked GND and two convex points must
face out. - Connect the electrical wires as shown in Fig 2, making sure
that all wire connectors are secured. If your junction box has a
ground wire, connect fixture’s ground wire to it. Otherwise,
connect the fixture’s ground wire directly to mounting plate using
green screw provided. - Place canopy over mounting plate and secure with screws.
- Place glass panel into metal frame and secure with tabs
provided. - Install four medium base bulbs up to 60 watts each or CFL or
LED equivalent in accordance with the fixture specification. DO NOT
EXCEED THE MAXIMUM WATTAGE RATING! - Return power to the junction box and test the fixture.
INSTALLATION INSTRUCTIONS
Item#N7814-726(Convertible Lamps for Pendant) (New. 2022/05/05) READ AND SAVE THESE INSTRUCTIONS
W AR NI N G ! S HU T P O WE R O F F AT F U S E O R CI R C UI T B R E AK E R .
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
MOUNTING THE FIXTURE (Fig.1)
Fig. 1
1. Shut off power at the fuse box or circuit breaker box and Set# A-021-118DH
remove the old fixture including the mounting hardware.
-Mounting plate
2. Carefully unpack your new fixture and lay out all the parts -Ground screw
in a clean area. Take care not to misplace any small parts -Mounting screws *2
necessary for installation.
3. Place metal frame (J) over metal tube (K) and secure with
screws (I).
F1
4. Determine the desired hanging height and thread rods (F1,
F2 and F3) to all thread (G) on fixture body. Attach canopy
(D) by threading onto rod (F1). Carefully feed wires through
each rod as you assemble. Note: Remove all thread, if
F2
installing with one 6″ rod only.
5. Attach mounting plate (A) to junction box (Not included)
with mounting screws (B) (Size: #8-32N*L0.5″). The side of
F3
mounting plate (A) marked “GND” and two convex points
must face out.
CONNECTING THE WIRES (Fig. 2)
6. Connect the electrical wires as shown in Fig 2, making sure
that all wire connectors are secured. If your junction box
has a ground wire (green or bare copper), connect fixture’s
ground wire to it. Otherwise, connect the fixture’s ground
wire directly to mounting plate (A) using green screw
provided.
7. Tuck wire connectors neatly inside the junction box.
FINISHING THE INSTALLATION (Fig.1)
8. Place canopy (D) over mounting plate (A) and secure with
G
screws (E).
9. Place glass panel (H) into metal frame (J) and secure with
tabs provided.
10. Install (4) four medium base bulbs (L) up to 60 watts each
or CFL or LED equivalent (not included) in accordance with
the fixture specification. — DO NOT EXCEED THE Rod# W30-1-66A *1 (F1)
MAXIMUM WATTAGE RATING! (NE PAS DEPASSER LA
W30-1-66A *2 (F2)
PUISSANCE NOMINALE MAXIMALE!)
W30-H-66A *1 (F3)
A B D E
H
I J
K
L
Your installation is now complete. Return power to the
junction box and test the fixture.
Fig. 2
Note: Illustration (Fig.1) on this manual is for installation purposes only. It may or may not be identical to the fixture purchased.
FIXTURE WIRES Black or Smooth
FIXTURE WIRES White or Ribbed HOUSE WIRES Black (Hot)
FIXTURE WIRES Bare Copper (Ground) HOUSE WIRES White (Neutral)
HOUSE WIRES Green (Ground)
Page:1/2
LA-3544E
INSTALLATION INSTRUCTIONS
Item# N7814-726 (Convertible Lamps for Semi Flush Mount) (New. 2022/05/05)
W A R N I N G ! S H U T íPOWERO FFATF UíES TEHOESRE ICNISRTCRUUCI TTIOBNRSE A K E R .
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEU
PREPARATION (Fig.3&4)
1. Loosen hex nut (O) by using wrench (M) (Not included). Carefully remove washer (P), lock washer (Q), metal plate (N), canopy (D) and swivels (S) (Fig.4). Cut down a length of wire if the wire is too long.
2. Secure the metal tube (R) into the all thread (G). 3. Thread canopy (D), metal plate (N), lock washer (Q),
washer (P) and hex nut (O) into the all thread on top of metal tube (R). Then secure hex nut (O) by using wrench (M)(Not included) .(Fig. 3) 4. Place metal frame (J) over metal tube (K) and secure with screws (I). 5. Attach mounting plate (A) to junction box (Not included) with mounting screws (B) (Size: #8-32N*L0.5″). The side of the mounting plate (A) marked “GND” and two convex points must face out.
CONNECTING THE WIRES (Fig. 2)
6. Connect the electrical wires as shown in fig 2, making sure that all wire connectors are secured. If your junction box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting plate (A) using the green screw provided.
7. Tuck wire connectors neatly into the junction box.
FINISHING THE INSTALLATION (Fig.3)
8. Place canopy (D) over mounting plate (A) and secure with screws (E).
9. Install the glass panel (H) into metal frame (J) and secure with tabs provided.
10. Install (4) four medium base bulbs (L) up to 60 watts each or CFL or LED equivalent (not included) in accordance with the fixture specification. –DO NOT EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!)
Fig. 3 Set# A-021-118DH -Mounting plate -Ground screw -Mounting screws*2
M N E D R
G
A B O P Q
H
I J
K
L
Your installation is now complete. Return power to the
junction box and test the fixture.
Fig. 4
M
Note: Illustration (Fig.3) on this manual is for installation
O
purposes only. It may or may not be identical to the
N
fixture purchased.
P Q
D
S
Page:2/2
LA-3544E
