2106-726 Townhall 6 Light Soft Brass and Coal Cage Pendant Light
Product Information
The product is a light fixture with the item number 2106-726.
The package includes a mounting plate, ground screw, junction box
screw, rod, candle cover, acrylic ball, and other hardware required
for installation. The fixture has wires for black or smooth, white
or ribbed, and bare copper (ground) connections. The manual
includes illustrations (Fig. 1-3) of the hardware and installation
process.
Product Usage Instructions
- Turn off the power at the fuse box or circuit breaker box
before installation. - Remove the old fixture and mounting hardware.
- Unpack the new fixture and lay out all parts.
- Refer to Fig. 1 to identify the mounting plate, ground screw,
junction box screw, rod, candle cover, and acrylic ball. - Refer to Fig. 2 for wiring instructions. Connect the black or
smooth fixture wire to the black (hot) house wire, the white or
ribbed fixture wire to the white (neutral) house wire, and the bare
copper fixture wire to the green (ground) house wire. - Refer to Fig. 3 for hardware identification. Use the hardware
bag to attach the mounting plate, junction box screw, canopy,
mounting screw, lock-up knob, quick link, and loop as shown in Fig.
3. - Attach the rod to the fixture using the hardware provided.
- Hang the fixture onto the mounting plate and secure it with the
lock-up knobs. - Attach the candle cover and acrylic ball to complete the
installation. - Turn on the power at the fuse box or circuit breaker box and
test the fixture.
Note: The illustration in Fig. 1 is for installation purposes
only and may not be identical to the fixture purchased.
INSTALLATION INSTRUCTIONS
Item#2106-726 (New.07/01/2022) READ AND SAVE THESE INSTRUCTIONS
W AR NI N G ! S HU T P O WE R O F F AT F U S E O R CI R C UI T B R E AK E R .
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
PREPARATION (Fig. 1) 1. Shut off power at the fuse box or circuit breaker box and
remove the old fixture including the mounting hardware. 2. Carefully unpack your new fixture and lay out all the parts
in a clean area. Take care not to misplace any small parts necessary for installation. ASSEMBLING THE FIXTURE WITH CHAIN LOOP (Fig.1&Fig. 3) 3. Place square tubes (L) on metal frame (N) and attach with countersunk screws (M) (Size: 8#-32N*L0.3″). 4. Align top frame (H) with square tubes (L) and attach with screws (T) (Size: 8#-32N*L0.3″) and cover the hole with plastic plug (S). 5. Screw metal tube (J) onto the all thread on light cluster (K). 6. Attach center rod (I) onto all thread on metal tube (J). 7. Thread center rod (I) into the all thread on top frame (H). 8. Place acrylic ball (Q) to bottom of fixture body (K) and secure with allen screw (O) using wrench (P) provided. 9. Determine the desired hanging height and thread rods (G1, G2) to the all thread of top frame (H). Then attach loop (F1) by screwing onto rod (G1). Pass the wires carefully through each rod as you assembled. 10. Attach quick link (E) connect to loop (F1) and loop (F2) on canopy (C), carefully feed the wire through loop (F1), quick link (E) and loop (F2). 11. Attach mounting plate (A) to the junction box (not included) with junction box screws (B) (Size: #8-32N*L1″). The side of the mounting plate (A) with “GND” marked on it and two convex points must face out. 12. The support cable is provided to support weight of fixture while wiring. Align fixture to mounting plate (A) and attach hook (W) on the end of support cable (V) into a slot located on mounting plate (A). Carefully allow support cable (V) to support weight of fixture while wiring (Fig.1 Fig3). CONNECTING THE WIRES (Fig. 2) 13. Connect the electrical wires as shown in fig.2, making sure that all wire connectors are secured. If junction box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting plate (A) using the green screw provided. 14. Tuck the wire connectors neatly into the junction box. COMPLETING THE INSTALLATION (Fig. 1) 15. Slide canopy (C) over mounting screws (U) attached to mounting plate (A) and secure with knobs (D). 16. Install (6) six candelabra base bulbs up to 60 watts each or CFL or LED equivalent (not included) in accordance with the fixture specification–DO NOT EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!)
Fig. 1 Set#A-020-A Mounting Plate x1pc Ground Screw x1pc Junction box Screw x2pcs
Rod# G1. W30-H-66A G2. W30-1-66A
Candle Cover# CCV20135P-695 Acrylic Ball# GP2105
Fig. 2
FIXTURE WIRES Black or Smooth
FIXTURE WIRES White or Ribbed
FIXTURE WIRES Bare Copper (Ground)
HOUSE WIRES Black (Hot)
HOUSE WIRES White (Neutral)
HOUSE WIRES Green (Ground)
Page 1/2
LA-3279E
Your installation is now complete. Return power to the junction box and test the fixture.
Note: Illustration (Fig. 1) on this manual is for installation purposes only. It may or may not be identical to the fixture purchased.
Fig.3
A
B
U
C
V
W
D
E
F2
F1
G1
a. Hardware Bag
A. Mounting Plate x 1pc
B. Junction Box
Screw x 2pcs
C. Canopy x 1pc
U. Mounting Screw x 2pcs
A
B
D. Lock-up Knob x 2pcs
E. Quick Link x 1pcs
F1. Loop x 2pcs
b. Hardware Bag G1. Rod 6″ x1pc G2. Rod 12″ x3pcs
C
U
D
E
F1
G1
Pa
Page 2/2
G2
LA-3279E
