2337-66A 1-Light Coal Bell Mini Pendant with Clear Glass Shade
Product Information:
Product Name: Item#2337-66A
Installation Instructions: READ AND SAVE THESE INSTRUCTIONS
Warning: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
Mounting Plate: Set# A020-102
Ground Screw: Included
Mounting Screw: Included (2)
Glass: G2337
Fixture Wires:
- Black or Smooth
- White or Ribbed
- Green or Bare Copper (Ground)
House Wires:
- Black (Hot)
- White (Neutral)
- Green (Ground)
Note: The illustration in this manual (Fig.1) is for
installation purposes only and may or may not be identical to the
fixture purchased.
Product Usage Instructions:
- Shut off the power at the fuse box or circuit breaker.
- If necessary, remove the old fixture and its mounting
hardware. - Carefully remove the new fixture from the carton and ensure all
parts are included. - Determine the desired hanging height and, if needed, cut the
cord accordingly. - Follow Fig.1 for assembling the fixture with cord.
- Connect the fixture wires as follows:
- Black or Smooth fixture wire to Black (Hot) house wire.
- White or Ribbed fixture wire to White (Neutral) house
wire. - Green or Bare Copper fixture wire (Ground) to Green (Ground)
house wire.
(Fig.1).
INSTALLATION INSTRUCTIONS
Item#2337-66A READ AND SAVE THESE INSTRUCTIONS
W ARNI N G ! SHUT P O WE R O FF AT F US E O R CI RC UI T BRE AK E R.
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
MOUNTING THE FIXTURE (Fig.1) 1. Shut off the power at the fuse box or circuit breaker. If
Pnaegcee:ss2a/3ry, remove the old fixture, including the mounting
hardware. 2. Carefully remove the fixture from the carton and check that all
parts are included as shown in the illustration. ASSEMBLING THE FIXTURE WITH CORD (Fig. 1) 3. Determine the desired hanging height and if necessary, cut the
cord leaving an additional 5” to allow for the electrical connections. 4. If need, use flathead screw driver to loosen the screw (J) to adjust length of cable wire, then tighten screw (J) until (K) is snug. 5. Attach mounting plate (A) to junction box (Not included) with screws (B). The side of the mounting plate (A) marked “GND” must face out. CONNECTING THE WIRES (Fig.2) 6. At this point, connect the electrical wires as shown in Fig.2, making sure that all wire connectors (I) are secured. If your junction box has a ground wire (green or bare copper), connect the fixture’ ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting plate (A) using the green screw provided. 7. Tuck wire connectors neatly into junction box. FINISHING THE INSTALLATION (Fig.1) 8. Place canopy (C) over mounting plate (A) and secure with canopy screws (D). 9. Unscrew metal cover (G) from socket (E). Position glass shade (F) onto socket and secure with metal cover (G). 10. Install (1) one medium base bulb (H) up to 60 watts each or CFL or LED equivalent (not included) in accordance with the fixture specification–DO NOT EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!).
Your installation is now complete. Return power to the junction box and test the fixture.
Fig. 1
Set# A020-102 -Mounting Plate -Ground Screw -Mounting Screw*2
J K
I A B D C
E
F G GLASS#G2337
H
Fig.2
FIXTURE WIRES Black or Smooth
FIXTURE WIRES White or Ribbed
FIXTURE WIRES Green or Bare Copper (Ground)
HOUSE WIRES Black (Hot)
HOUSE WIRES White (Neutral)
HOUSE WIRES Green (Ground)
Note: Illustration (Fig.1) on this manual is for installation purposes only. It may or may not be identical to the fixture purchased.
Page: 1/2
2337-66A
Fig.3
Page: 2/2
2337-66A
