MRS BLE Only Mortise Lock
Product Information: MRS BLE Only Mortise Lock
The MRS BLE Only Mortise Lock is a mechanical lock that can be
installed on doors. The lock comes with a hardware kit (W51411),
which includes a dead latch slider and a strike screw pack. The
lock is available in two handings – LH/LHR and RH/RHR. The lock
also includes Orlando/Memphis levers & ball knob.
Product Usage Instructions:
- Check the handing of the lock body.
- Prepare the door by using the hardware kit, W51411, and
installing the dead latch slider. - Prepare the jamb by using the strike screw pack.
- Attach the lever by assembling the rose as shown and using the
supplied hex key to tighten the socket head cap screw. For
Orlando/Memphis levers & ball knob, skip this step and refer to
step 6. - Install the drive spindles/outside trim by retracting the latch
and confirming the spindle engagement. - Install the inside trim/rose by installing the spindle with the
lever and securing it with machine screws supplied in the hardware
kit, W51411. Confirm the spindle engagement and secure the rose
plate by rotating clockwise until tight. For Orlando/Memphis levers
& ball knob, tighten from underside with supplied hex key. - Install the cylinder, turnpiece, and armor plate by installing
the cylinder trim collar and turning it slightly recessed. Install
the slotted set screw through the I/C bore to secure the housing
for I/C housings. Install screws supplied in the thumb turn screw
pack. - Install the inside mounting plate assembly and push extra wire
into the door cavity. Secure it. - Install the battery pack over two studs on the mounting plate
and snap it onto retainers on the mounting plate. Plug in battery
wire to control board. - Install batteries and battery cover with (2) black pan head
screws.
MRS INSTALLATION INSTRUCTIONS
BLE ONLY MORTISE LOCK
For Mechanical Concerns: Phone: 866-874-3662 www.pdqlocks.com
LH/LHR
RH/RHR
1. CHECK HANDING OF LOCK BODY
· If handing of lock body is not correct for opening, consult factory for handing instruction.
2. DOOR PREPARATION
· Prepare the door for the mortise lock. · Install the mortise case while feeding chassis wire into
hole on inside of door. · Gently pull wire through hole as chassis is inserted · Secure using two (2) combo screws supplied in the
hardware kit, W51411
Dead Latch Slider
3. JAMB PREPARATION
· Prepare the jamb for the mortise lock strike. · Install Dead Latch Plate behind strike with slider toward bottom for
dead latch. · Install the strike and secure with two (2) combo screws supplied in
the strike screw pack.
4. LEVER ATTACHMENT
· Assembly Outside Lever – If outside scalp was removed, install scalp.
Assemble rose as shown using the supplied hex key to tighten the socket head cap screw.
Orlando/Memphis Levers & Ball Knob – Skip the following step. Do not install inside lever and discard one (1) socket head cap screw. Refer to step 6.
· Assembly Inside Lever Remove inside scalp. Assemble the inside rose as
shown using the supplied hex key to tighten the socket head cap screw.
Inside Outside Rev0 5-26-23
MRS MORTISE LOCK
Short Ends Into Case
SPINDLE ORIENTATION
INCORRECT CORRECT
5. INSTALL DRIVE SPINDLES / OUTSIDE TRIM
Drive Spindles: · Install drive spindles and springs on both sides in orientation shown.
Outside Trim · Install outside trim to door while aligning lever with drive spindle. · Confirm spindle engagement in lock by rotating the lever down,
retracting the latch.
6. INSTALL INSIDE TRIM / ROSE
· Install the inside rose assembly to the inside of the door. Align
the spindle with the lever.
· Secure inside rose assembly with 1-1/2″ long flat head
machine screws, supplied in the hardware kit, W51411 Confirm the spindle engagement.
· Install the rose scalp by aligning the dimples with the slots in
the rose plate. Secure by rotating clockwise until tight.
FOR ORLANDO/MEMPHIS LEVERS & BALL KNOB
· Slide lever onto spindle. Install set screw in bottom of lever.
Tighten from underside with supplied hex key.
Orlando Memphis Ball Knob
Only
7. CYLINDER, TURNPIECE AND ARMOR PLATE INSTALLATION
· Assembly cylinder, cylinder spring and cylinder trim collar. · Thread the cylinder into the lock body until the cylinder is flush or
slightly recessed in the cylinder trim collar.
· Secure the cylinder by tightening set screw through front of case,
on the side of cylinder, with the hex key provided in the hardware kit, W51411. For I/C housings, install the slotted set screw through the I/C bore to secure the housing.
· Install the turnpiece and secure with two (2) truss head sheet metal
screws, supplied in the thumb turn screw pack.
· Install the armor plate with two (2) flat head machine screws.
Rev0 5-26-23
MRS MORTISE LOCK
INSIDE MOUNTING PLATE
CHASSIS WIRE
CHASSIS WIRE SLOT
9. INSTALL BATTERY PACK
Plug in battery wire to control board. Install battery pack over two studs on
mounting plate. Snap battery pack onto retainers on
mounting plate.
8. INSTALL INSIDE MOUNTING PLATE ASSEMBLY
· Install inside mounting plate assembly. · Feed chassis wire through T slot in
mounting plate. · Secure with (4) pan head wood/metal
screws. · Make wire connection after reader is
secure. Push extra wire into door cavity.
BATTERY RETAINERS
BATTERY PLUG
BATTERY COVER
BATTERY PACK
11. INSTALL BATTERIES AND BATTERY COVER
Install batteries and battery cover with (2) black pan head screws.
Rev0 5-26-23
Home Page | PDQ
