AR6204350 8 Inch Widespread Double-Handle Bathroom Faucet
Product Information: TWO HANDLE LAVATORY CENTERSET FAUCETS
This product is a two-handle lavatory centerset faucet. It is
designed for easy installation and comes with a 1.2GPM (4.5L/min)
aerator. The faucet is compliant with California water efficiency
regulations and complies with California Proposition 65 and the
Federal Safe Drinking Water Act. The finish of this faucet is
extremely durable, but it can be damaged by harsh abrasives or
polish.
Product Specifications:
- Hole Size: 1.26 to 1.5 (32mm to 38mm)
- Pre drilled hole size: 1.26 to 1.5 (32mm to 38mm)
- Unsuitable sink size: 1 (25mm) Hole Size
- Max. deck Thickness: M14mm
Product Usage Instructions:
Installation:
- Before installing the valves, clean the water pipe thoroughly
to avoid dirt and deposits. - Install the spout (1) O-ring (2) and secure with the washer and
nut (3). If the sink is uneven, use silicone under the gasket. - Remove the brass lock nut from the thread rod counter-clockwise
and remove the washer and washer. - Attach the gasket to the base of the hot (1) and cold (2) end
valves. - Slide the hot (1) and cold (2) end valves with flexible hoses
(3) through the sink. - Place the washer (4) and metal plate (5) over the mounting stud
under the sink and secure with the mounting nut (6). - Lock the mounting nut (6) into position by tightening the screw
(7). - Apply teflon tape to the quick connect installation.
- Align tabs and tabs on quick connects. Push quick connects
firmly upward and snap onto the receiving tube tab. Pull down
moderately to ensure each connection has been made. - Remove the washer (2), black gasket (4), and nut (5) from the
assembly. - Slide the washer (2) up to the underside of the flange (3).
Insert the flange (3) and washer (2) into the sink and secure with
the black gasket (4) washer and nut (5) from underneath the
sink. - Put down and check the spring-loaded stopper (1).
- Connect the assembly to the drain.
Cleaning and Care:
Care should be given to cleaning this product. Although its
finish is extremely durable, it can be damaged by harsh abrasives
or polish. To clean, simply wipe gently with a damp cloth and blot
dry with a soft towel.
Flushing Debris from Plumbing System:
- Remove the aerator by hand.
- Run hot and cold water for one minute.
- Replace the aerator.
Checking for Leaks:
Repeat the following steps for each hose connection:
- Make sure the hose with the hot label is connected to the hot
supply valve, and the other hose is connected to the cold supply
valve. - Turn on hot and cold water supplies and flush water lines for
one minute. - Check all connections at arrows for leaks.
- Retighten if necessary, but do not overtighten.
TWO HANDLE LAVATORY CENTERSET FAUCETS
You may need
1.2GPM 4.5L/min
For easy installation of your faucet you will need:
To READ ALL the instructions completely before beginning.
To READ ALL warnings, care, and maintenanceinformation.
With 1.2 gpm are compliant with California water effi ciency regulations, Complies with California Proposition 65 and with the Federal Safe Drinking Water Act.
washer 1.2gpm aeratot
In areas with extremely low water pressure causing the basin faucet water flow to be unsatisfactory ,
aeratot house
replace the 2.2 gpm aerator to improve the water flow in the basin faucet.
Cleaning and Care Care should be given to the cleaning of this product. Although its finish is extremely durable, It can be damaged by harsh abrasives or polish. To clean, simply wipe gently with a damp cloth and blot dry with a soft towel.
1.26″ to 1.5″ (32mm to 38mm)
Hole Size
4″-16″ (100-400mm)
Ø1″(25)
4″ (100mm)
Pre drilled hole size : 1.26″ to 1.5″(32mm to 38mm)
Hole Size
Unsuitable sink size
1″(25mm) Hole Size
11″to21″ (280mm to 535mm)
6″to16″ (152mm to 406mm)
4.4″
(113mm) 7.5″
(191mm)
Hot
2.7″ (68mm)
1.2″(30mm)
Max. deck
Thickness
M14mm
3x Ø2 (Ø52 mm)
4.7″ (120mm)
3×1.26″ to 1.5″
(32mm to 38mm)
Hole Size
Ø2.2″ (55mm)
1.1″ to 2.5″ (28 to 64mm)
9.5″(240mm) 8.7″(220mm)
3/8″
”
:”(
Min. 1.6″ (Ø41mm) Hole Dia
1 1/4” (Ø32mm)
OPERATION
· Double levers style handles · Maximum handle(s) rotation angle is 90° to full on · Rotate hot side counter clockwise to open (clockwise to close) · Rotate cold side clockwise to open (counter clockwise to close)
Notes
1
1 Before installing the valves, clean the water pipe thoroughly to avoid dirt and deposits.
1
2 3
Install spout (1) O-ring (2) , Secure with washer and nut (3). Note: If sink is uneven, use silicone under the gasket.
2
Remove the brass lock nut from the thread rod counter-clockwise, remove the washer and washer.
3
4
1 2
3
4 5
6
7
1.Make sure attach the gasket to the base of hot (1) and cold (2) end valves. 2.Slide hot (1) and cold (2) end valves with flexible hoses (3) through sink. 3.Place washer(4) and metal plate(5) over mountingstud under sink. Secure with mounting nut(6). 4.Lock mounting nut(6) into position by tightening screw (7).
NOT WITH apply teflon tape to the quick connect installation.
Align tabs and tabs on quick connects . Push quick connects firmly upward and snap onto receiving tube tab . Pull down moderately to ensure each connection has been made.
5
1
2 3
4 5
6 1.
1.Remove the washer (2) , black gasket (4) and nut (5) from the assembly. 2.Slide washer (2) up to underside of flange (3). Insert flange (3) and washer (2) into sink and secure with the black gasket (4) washer and nut (5) from underneath the sink. 3.Put down and check the Springloaded stopper (1). 4. Connect assembly to drain.
7
2. 3.
To flush debris from the plumbing system: 1.Remove the aerator by hand. 2.Run hot and cold water for one minute. 3.Replace the aerator.
Repeat for other hose connection making sure the hose with the hot label is connected to the hot supply valve and the other hose is connected to the cold supply valve. FLUSH SYSTEM/CHECK FOR LEAKS. Turn on hot and cold water supplies and flush water lines for one minute. Check all connections at arrows for leaks. Retighten if necessary, but do not overtighten.
