Arcora Ar62115a3g Single Handle Centerset Bathroom Faucets Instruction Manual

AR62115A3G Single Handle Centerset Bathroom Faucets

Product Information:

• Product Name: Single Handle Centerset Bathroom Faucets
• Product Dimensions: 6.1×2.4×0.3 inches (155x62x8.5 mm)
• Weight: 4.8 ounces (123 grams)
• Flow Rate: 1.2 gallons per minute (1.2gpm)
• Max. Deck Thickness: 1.2 inches (30mm)
• Hole Size: Pre-drilled hole size should be between 1.26 to 1.5
  inches (32mm to 38mm)

Product Usage Instructions:

1. Before beginning the installation, read all the instructions
   and warnings provided.
2. Clean the water pipe thoroughly to remove any dirt or deposits
   before installing the valves.
3. Attach the mounting stud under the faucet body.
4. Attach the flexible hoses under the faucet body.
   1. Remove the washer (2), black gasket (4), and nut (5) from the
      assembly.
   2. Slide the washer (2) up to the underside of the flange
      (3).
   3. Insert the flange (3) and washer (2) into the sink and secure
      them with the black gasket (4) and nut (5) from underneath the
      sink.
   4. Put down and check the spring-loaded stopper (1).
   5. Connect the assembly to the drain.
5. Make sure to attach the O-ring (1) to the base of the faucet
   body.
6. Slide the decorated plate with gasket (2) up over the tubes and
   mounting stud.
7. Slide the tubes down through the mounting hole and faucet, with
   the decorated plate with gasket (2) on the sink.
8. Optionally, if the sink is uneven, use silicone under the
   gasket.
9. Place the washer (3) and metal plate (4) over the mounting stud
   under the sink and secure them with the mounting nut (5).
10. Make sure to attach the O-ring (1) to the faucet body.
11. Slide the tubes down through the mounting hole on the
    sink.
12. Optionally, if the sink is uneven, use silicone under the
    faucet body.
13. Place the washer (2) and metal plate (3) over the mounting stud
    under the sink and secure them with the mounting nut (4).
14. Secure the metal nut on the faucet supply hoses to the supply
    valve connection and hand tighten.
15. Tighten one additional revolution with a wrench. Do not
    overtighten.
16. Repeat the above step for the other hose connection, ensuring
    that the hose labeled “hot” is connected to the hot supply valve
    and the other hose is connected to the cold supply valve.
17. Do not use pipe dope or other sealants on water
    connections.
18. Flush the system and check for leaks. Turn on the hot and cold
    water supplies and flush water lines for one minute.
19. Check all connections at arrows for leaks. Retighten if
    necessary, but do not overtighten.

SINGLE HANDLE CENTERSET BATHROOM FAUCETS
You may need
For easy installation of your faucet you will need:
To READ ALL the instructions completely before beginning. To READ ALL warnings, care, and maintenanceinformation.
Cleaning and Care Care should be given to the cleaning of this product. Although its finish is extremely durable, It can be damaged by harsh abrasives or polish. To clean, simply wipe gently with a damp cloth and blot dry with a soft towel. With 1.2 gpm are compliant with California water effi ciency regulations, Complies with California Proposition 65 and with the Federal Safe Drinking Water Act. In areas with extremely low water pressure causing the basin faucet water flow to be unsatisfactory , replace the 2.2 gpm aerator to improve the water flow in the basin faucet.
washer 1.2gpm aeratot aeratot house

6.1″x2.4″x0.3″ (155x62x8.5)

1.9″x1.9″ (49×49)

4.8″(123)

1.2″(30mm) Max. deck Thickness 24″(600mm)

Ø1.26″(32) M10x1mm

Ø2.2″ (56mm)

1.1″ to 2.5″ (28 to 64mm)

9.5″(240mm) 8.7″(220mm)

3/8″
Min. 1.6″ (Ø41mm) Hole Dia
1 1/4” (Ø32mm)

Ø1.4″(Ø35)

unit:inch(mm)

Ø1.4″(35mm)

Ø1.4″(35mm)
6″ (150mm)

Ø1-Ø1.18″ (25-30mm)
4″ (100mm)

Pre drilled hole size : 1.26″ to 1.5″(32mm to 38mm)
Hole Size

Unsuitable sink size
1″ to 1.2″(25mm to 30mm) Hole Size

9″(228.5) 8″(203.5) 5.5″(138.5)

Notes

1

2

Before installing the valves, clean the water pipe thoroughly to avoid dirt and deposits.

1

Hot Cold

Attach mounting stud under faucet body

Attach flexible hoses under the 5 faucet body.

3.A

3.B

4
1
2 3
4 5
5

1.Remove the washer (2) , black gasket (4) and nut (5) from the assembly. 2.Slide washer (2) up to underside of flange (3). Insert flange (3) and washer (2) into sink and secure with the black gasket (4) washer and nut (5) from underneath the sink. 3.Put down and check the Springloaded stopper (1). 4. Connect assembly to drain.
6

1 2
3 4 5

1
2 3 4

1.Make sure attach the O-ring(1) to the base of faucet body. 2. Slide 6″decorated plate with gasket(2) up over tubes and mounting stud. Slide tubes down through mounting hole andfaucet, 6″decorated plate with gasket (2) on sink. Option: If sink is uneven, use silicone under the gasket. 3.Place washer(3) and metal plate(4) over mounting stud under sink. Secure with mounting nut(5).

1.Make sure attach the O-ring(1) to the faucet body. 2.Slide tubes down through mounting hole on sink. Option: If sink is uneven, use silicone under the faucet body. 3.Place washer(2) and metal plate(3) over mounting stud under sink. Secure with mounting nut(4).

Hot hose Hot

Cold hose Cold

Secure metal nut on faucet supply hoses to supply valve connection and hand tighten, then tighten one additional revolution with wrench. DO NOT OVERTIGHTEN. Repeat for other hose connection making sure the hose with the hot label is connected to the hot supply valve and the other hose is connected to the cold supply valve. WARNING: Do not use pipe dope or other sealants on water connections.

FLUSH SYSTEM/CHECK FOR LEAKS. Turn on hot and cold water supplies and flush water lines for one minute. Check all connections at arrows for leaks. Retighten if necessary, but do not overtighten.