Huanuo Dual Monitor And Laptop Mount Instruction Manual

Dual Monitor and Laptop Mount

Dual Monitor and Laptop Mount
Instruction Manual

75x75mm 100x100mm

(2~9kg)x3 (4.4~19.8lbs)x3

If you have any questions, please feel free to contact our customer service via Amazon.

AHP-53-US1.0

WARNING!
If you have any confusions or are not quite sure about the installation, please do not hesitate to ask for our help.
Before assembly, please check and make sure all necessary accessories are included and undamaged. Improper installation, such as use the product for monitors over its load capacity or for any purpose not explicitly specified, may cause damage or serious injury. We would not be liable for any damage or injury caused by improper mounting or inappropriate use.
The kit contains small items that could be choking hazards if swallowed. Please keep them OUT OF REACH OF CHILDREN UNDER 3 YEARS OLD. ADULT SUPERVISION IS REQUIRED.
PACKAGE CONTENTS
All are included in B
Bolts B3(x2)

A (x1) Arm

A1 (x2) Cable Cover

B (x1) Clamp

Bracket B1

Bolt Y B2

B-1 (x1) Clip Plate

C (x1)

D (x2)

Decorative cover VESA Plate

E (x1) Laptop Tray

F(x1) Base

G (x1) Middle Arm

E1 (x5) Pad

F1(x3) Pad

F2 (x1) Wire clip

G1 (x1) Wire clip

H (x2) Bolt

I (x2) Plastic Parts

J(x1) 3mm Allen Key

K(x1) 5mm Allen Key

L(x1) 6mm Allen Key

M(x1) 8mm Box Spanner

M-A (x8) M4x12mm

M-B (x8) M4x30mm

M-C (x8) Washer D5mm

M-D (x16) Spacer H5mm

M-E (x4) M5x12mm

M-F (x4) M5

(2~9kg)x3
DO NOT EXCEED WEIGHT CAPACITY. (4.4~19.8lbs)x3
01

NOTE: Not all hardware included will be used.

ASSEMBLY STEPS
STEP 1: Apply Pads To The Base Bottom
Paste the Pad (F1) onto the Base (F) F1
F

STEP 2: Clamp Installation Or Grommet Base Installation
OPTION A: Clamp Installation Align the screw hole on the Base (F), then lock the Screw (B3) with a 5mm Allen Key (K). Put the Clip Plate (B-1) on the Bolt Y (B2)
K
F

B

B-1

Fix the bracket on the table by tightening the Clamp (B), then fix the Decorative Cover (C) to the Base (F).

C F
Min10mm~Max50mm

02

STEP 2: (Continued)
OPTION B: Grommet Base Installation

0.39”~2.36” 10mm~60mm

Ensure the desktop has a hole between 0.39”~2.36” (10mm~60mm) in diameter to use this option.

Use 5mm Allen Key(K) to detach Bolts(B3)and Bolt Y(B2) from Clamp(B). K

B2

B3

B1

Use Bolt Y (B2) through the screw hole on Bracket (B1) to fix the base (F) and the table board together. Then fix the Decorative Cover (C) to the Base (F).

F B1
B2

C Min10mm ~Max50mm
03

STEP 3 : Arm Installation
1: Install Wire Clip (F2) and Swivel Arm (A) to the pole. Lock the bolt on Swivel Arm (A) with supplied 6mm Allen key (L).
2-1: Install Wire Clip (G1) to Middle Arm (G). 2-2: Install Plastic Parts (I) to Middle Arm (G). 2-3: Install Middle Arm (G) to the pole, then Lock the bolt on Middle Arm (G) with supplied 6mm Allen key (L).

G
A F2
1
L

UP
2-1
G1 I
2-2

2-3 L
04

STEP 4 : Front-panel Installation
Install Laptop Tray (E) to the Middle Arm (G), Apply pads (E1) to the Laptop Tray (E) to avoid laptop scratches.
E1

1

E

2

3

M-F M

M-E
J

M-E

M

1. Install the top two screws first 2. And then you attach the Laptop Tray (E) to the Middle Arm (G) 3. Finally install the next two screws and tighten all screws

05

M-F J

STEP 5 : Attach Monitor
OPTION A: Flat Back Monitor
Attach the VESA plate (D) to the back of monitor and secure it by using a 5mm Allen Key (K) to tighten screws (M-A) along with washers (M-C).

UP

D

Do not tighten the screws excessively or your monitor might be damaged.
OPTION B: Curved Back Monitor
Attach the VESA plate (D) to the back of monitor and secure it by using a 5mm Allen Key (K) to tighten screws (M-A) along with washers (M-C) and Spacer (M-D).

Monitor

Monitor Monitor

K
M-A M-C

monitor

monitor monitor

UP D
Do not tighten the screws excessively or your monitor might be damaged. NOTE: Hand tighten screws to avoid over tightening.
06

K M-B M-C
M-D one or two piece

STEP 6 : Hang Monitor
Slide the monitor onto the head of Swivel Arm (A). Install the Security Bolt (H). Make sure the security bolt is tightened before you rotate the monitor.
H

Important Notice: The pressure of the gas spring is initially set at the lowest value. So when the monitor is hung on, make sure you hold it with both hands and DO NOT let it go down suddenly.
STEP 7 : Tilt Adjustment

+
–
K

1. Slightly loosen the tilting bolt. 2. Adjust monitor and laptop tray to your desired tilt angle. 3. Retighten tilting bolt to secure the monitor and front-panel in place.
07

STEP 8 : Gap Spring Tension Adjustment
For intended functioning of the mount, you may need to adjust the tension of Arm (A) in accordance with your monitor weight by 6 mm Allen Key (L).
L

CAUTION

Note1:
Be sure to keep the arm in horizontal position during adjustment. Or else it would be difficult to adjust the mount ordamage the mount.

Situation 1: Arm falls down Upper Arm with monitor falls down and fails to stay where intended.
Solution: Turn the inside screw counterclockwise(“+”direction) to increase gas spring tension until the arm can stay as intended.

Situation 2: Arm rises up Upper Arm with monitor rises up and fails to stay where intended.
Solution: Turn the inside screw clockwise(“-“direction) to decrease gas spring tension until the arm can stay as intended.
Note2:
For how many circles the screw should be turned, please refer to the table below.

(AT LEAST) min 2

46

08

8 10 12 15

STEP 9 : Cable Management
Run cables through the cable cover as shown in diagram.
Cable Cover
Push and Slide Remove the harness cap

Insert
A1
Insert two tabs (on the inside)

Insert and Push

Run cables through the cable cover (A1), then press the two tabs (on the inside) on one side of the cable cover(A1) slightly inward to insert the cable cover(A1) to upper arm (A) as shown in diagram.
09

Adjust as Desired
Adjust monitor position and rotation.
Tilt Swivel Rotation

Swivel ±90°

±180° Rotation

+90°
Tilt
-90°

Swivel ±180°

Swivel ±90°

±135°
Swivel K L

Swivel ±90°

Caution:
Please be careful to avoid Laptop falling off during use.

DESK

DESK

Please do not move stand outside desk for safety!
Note: To ensure stability, the tightness of the rotating axis has been preset, so it would be kind of difficult to rotate the VESA plate. Suggestion: Please attach the monitor first, then hold the two sides of it with both hands, and rotate vigorously. If that doesn’t work out, please do not hesitate to ask for our help.

10

9.45″/240mm max: 11.42″/290mm
10.63″/270mm

Product Dimensions Unit Conversion
1 CM0.39 inch
36.22″~40.16″ 920mm~1020mm

172053.90m.95m”4m”m
1144.5m”m

1.85″ 47mm

7.28″ 185mm

35mm

Swivel 180°
2.36″ 60mm 8.46″~10.83″ 215~275mm
+90° Tilt -90°

15.24″/387mm

Swivel ±135°
1″/25mm 0.39~1.97″/10~50mm

6.783.9″”//127216mmmm

+90° Tilt -90°

2.95″ 75mm
3.94″ 100mm
4.5” 114mm

1703520.9.m9m45m””m 1144.5m”m

±180°

CAUTION AND MAINTENANCE:
Don’t allow children to climb, stand, hang, or play on any part of monitor or stand. This product is intended for indoor use only. Using this product outdoors may lead to product
damage or personal injury. Check if that the bracket is secure and safe to use at regular intervals
(at least every three months).
11