F14181-QC 1-Light Matte Black Outdoor Pendant Light
Product Information
The product is a light fixture that requires assembly and
installation. It comes with a mounting unit, a fixture, a cover,
threaded pipe and hex nut, rubber rings, nuts, iron, decorative
nut, screws, wire nuts, and mounting screws. The product also
requires tools such as a ladder, safety glasses, electrical
Phillips screwdriver, flat blade screwdriver, pliers, wire
strippers, and tape for assembly and installation.
Product Usage Instructions
- Before assembly and installation, ensure to turn off the power
supply to the junction box by removing the fuse at the fuse
box. - Use the provided mounting screws to attach the mounting unit to
the junction box. Unscrew the rubber rings and screws from the
mounting unit before attaching it. - Screw the threaded pipe and hex nut into the fixture and secure
it with a hex nut. - Place the top cover onto the threaded pipe and secure it with
rubber ring A and nut. - Attach the iron to the fixture through screw holes as shown in
the manual and secure it with rubber ring B and decorative
nut. - Make the electrical connection from the junction box to the
fixture. Connect the ground wire to the mounting unit using the
preinstalled green ground screw. Then connect the positive,
negative, and ground wires with the supplied wire nuts and secure
them with electrical tape. Connect black or red wire (hot) from the
junction box, white wire (neutral) from the junction box, black
wire from the fixture, white wire from the fixture, and bare or
green ground wire from the junction box. - Attach the fixture to mounting unit through screw holes and
secure it with screws. - Install bulbs (not included).
- After installation, use caulk in the back plate and wall
mounting surface to prevent water from entering.
ASSEMBLY INSTRUCTIONS
CAUTION
³Inspect the wire insulation for any cuts, abrasions, or exposed copper that may have resulted during shipping. If there is a defect in the wire, do not attempt installation.
TOOLS REQUIRED
³Before starting installation of this fixture or removal of a previous fixture, disconnect the power by turning off the circuit breaker or by
removing the fuse at the fuse box.
Ladder
Safety glasses
Electrical Phillips
tape
screwdriver
Flat blade screwdriver
Pliers
Wire strippers
HARDWARE INCLUDED
Fixture
Cover
Threaded Pipe and Hex Nut
Rubber Ring A
Nut
Iron
Rubber Ring B
Decorative Nut
Mounting Unit
Screws
Mounting Screws
Wire Nuts
*PARTS SHOWN MAY DIFFER SLIGHTLY PER LIGHT FIXTURE
EXPLODED PARTS
Iron Decorative Nut
INSTALLATION
STEP 1
Nut
Unscrew the rubber rings and screws from the mounting unit.
Use the mounting screws to attach the mounting unit
to the junction box.
Rubber Ring B
Rubber Ring A Cover
Threaded Pipe and Hex Nut
Fixture
Mounting Screws
Wire Nuts Mounting Unit
Screws
STEP 2
Screw the threaded pipe and hex nut into the fixture, then secure it with hex nut.
Bulbs (not included)
ASSEMBLY INSTRUCTIONS INSTALLATION
STEP 3
Place the top cover onto the threaded pipe, then secure with rubber ring A and nut.
STEP 4
Attach the iron to the fixture through screw holes as shown, and secure it rubber ring B and decorative nut.
STEP 5
Make the electrical connection from the junction box to the fixture. Connect the ground wire to the mounting unit using the preinstalled green ground screw. Then, connect the positive, negative and ground wires with the supplied wire nuts. Secure with electrical tape.
Black or Red wire (hot) from the junction box
White wire (neutral) from the junction box
Black wire from the fixture
White wire from the fixture
Bare or Green ground wire from the junction box
*Sealing tape (not included)
Ground wire from the Fixture
*Green Ground Screw
NOTICE: Please use caulk in the back plate and wall mounting surface to prevent water from entering.
STEP 6
Attach the fixture to mounting unit through screw holes as shown, and secure it with screws.
STEP 7
Install bulbs (not included).
