NF51436-02i Goo 6 Light 16 Inch Geometric Lantern Pendant Light
Product Information
This product is a light fixture that includes an iron rack,
chain, mounting unit, and canopy. It requires assembly and
installation, and the following tools are required: ladder, safety
glasses, electrical Phillips screwdriver, flat blade screwdriver,
pliers, and wire strippers.
Hardware included in the package are fixture, ball nuts,
mounting screws, wire nuts, screw collar, mounting unit screws,
chain, ring, iron rack, and canopy. The product requires bulbs to
be installed (bulbs not included).
Product Usage Instructions
- Attach the iron rack onto the fixture using ball nuts.
- Attach the end of the chain to the loop on the fixture using
ball nuts. - Use the mounting screws to attach the mounting unit to the
junction box. - Pass the chain and branch wires through the screw collar ring
and canopy. Feed the branch wires through the pipe nipple on the
mounting unit and attach the end of the chain to the mounting
unit. - Make the electrical connection from the junction box to the
fixture. Connect the ground wire to the mounting unit using the
preinstalled green ground screw. Then, connect the positive,
negative, and ground wires with the supplied wire nuts. Secure with
electrical tape. The black or red wire (hot) from the junction box
should be connected to the smooth side of wire from the fixture
identified with the label L. The white wire (neutral) from the
junction box should be connected to the ribbed side of wire from
the fixture identified with the label N. The bare or green ground
wire from the junction box should be connected to the ground wire
from the fixture. - Secure the canopy to the mounting unit with the screw collar
ring. - Install bulbs (not included).
Note: Before starting the installation process, it is important
to remove the fuse at the fuse box. Also, the parts shown in the
manual may differ slightly per light fixture.
Caution: Always wear safety glasses during installation, and
make sure to follow all instructions carefully to ensure proper
installation and avoid any accidents or damage.
Assembly Instructions
CAUTION
· Inspect the wire insulation for any cuts, abrasions, or exposed copper that may have resulted during shipping. If there is a defect in the wire, do not attempt installation.
· Before starting installation of this fixture or removal of a previous fixture, disconnect the power by turning off the circuit breaker or by
removing the fuse at the fuse box.
TOOLS REQUIRED
Ladder
Safety glasses
Electrical Phillips
tape
screwdriver
Flat blade screwdriver
Pliers
Wire strippers
HARDWARE INCLUDED
Fixture
Iron Rack
Ball Nuts
Chain
Screw Collar
Mounting
Canopy
Ring
Mounting Unit Screws Wire Nuts
*PARTS SHOWN MAY DIFFER SLIGHTLY PER LIGHT FIXTURE
EXPLODED PARTS
INSTALLATION
STEP 1
Attach the iron rack onto fixture using ball nuts.
Wire Nuts
Mounting Screws
Mounting Unit
Canopy
Screw Collar Ring
Chain
Fixture
STEP 2
Ball Nuts Attach the end of the chain to the loop on the fixture.
STEP 3
Use the mounting screws to attach the mounting unit to the junction box.
Bulbs (not included)
Iron Rack
Assembly Instructions
INSTALLATION STEP 4
Pass the chain and the branchwires through the screw collar ring and canopy. Feed the branchwires through the pipe nipple on the mounting unit and attach the end of the chain to the mounting unit.
STEP 5
Make the electrical connection from the junction box to the fixture. Connect the ground wire to the mounting unit using the preinstalled green ground screw. Then, connect the positive, negative and ground wires with the supplied wire nuts. Secure with electrical tape
Black or Red wire (hot) from the junction box
White wire (neutral) from the junction box
Bare or Green ground wire from the junction box
*Sealing tape (not included)
Smooth side of wire from the fixture identified with the label “L”
Ribbed side of wire from the fixture identified with the label “N”
Ground wire from the Fixture
*Green Ground Screw
STEP 6
STEP 7
Secure the canopy to the mounting unit with the screw collar ring. Install bulbs (not included)
