P5334-077-L LED Wall Mount
Product Information: P5334-077-L LED Wall Mount
The P5334-077-L is an LED wall mount designed for indoor use. It
comes with a mounting plate, ground screw, and mounting screw for
easy installation. The fixture is compatible with ELV and/or LED
compatible wall dimmer switches and is dimmable. Please note that
the illustration in the manual is for installation purposes only
and may not be identical to the fixture purchased. For safety
reasons, it is important to have a qualified electrician install
the fixture to ensure proper wiring and installation.
Product Usage Instructions:
- Before beginning installation, read and save the instructions
provided with the fixture. - Shut off power at the fuse or circuit breaker before starting
installation. - Attach the mounting plate to the junction box using the
provided mounting screw. - Connect the ground screw to the grounding wire in the junction
box. - Attach the fixture to the mounting plate using the screws
provided in Set#A-020-176. - Turn on power to the junction box and test the fixture.
- If you wish to dim the fixture, use ELV and/or LED compatible
wall dimmer switches.
INSTALLATION INSTRUCTIONS FOR P5334-077-L For LED Wall Mount
READ AND SAVE THESE INSTRUCTIONS
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DO DISJONCTEU
ASSEMBLING THE FIXTURE (Fig.1) 1. Shut off power at the fuse box or circuit breaker box and remove the old fixture including the mounting hardware. 2. Carefully unpack your new fixture and lay out all the parts in a clean area. Take care not to misplace any small parts necessary for installation. 3. Unscrew screws (G) to remove mounting plate (A) from backplate (F). 4. Attach mounting plate (A) to the junction box (Not included) using the mounting screws (B, size 8#-32N 1/2″). The side of the mounting plate (A) marked “GND” must face out as shown in Fig.1. CONNECTING THE WIRES (Fig. 2) 5. Pass the black/white and bare copper wires through the opening of the mounting plate (A). Connect the electrical wire as shown in figure 2, making sure that all wire connectors are secured. If your junction box has a ground wire (green or bare copper), connect the ground wire from the fixture to it. Otherwise connect fixture ground wire directly to the mounting plate (A) using the green screw (D) provided. Tuck the wire connections neatly into the junction box. FINISHING THE INSTALLATION (Fig.1) 6. Place backplate (F) over mounting plate (A) secure with screws (G). 7. Hang crystals (E and E1) to the fixture. CAUTION/ATTENTION: When handling the fixture, do not apply pressure to the LEDs. Hold the fixture by the frame only. Replacing LED module (Fig. 3) The LED module can be replaced by a qualified electrician without cutting of wire and without damage to any decorative element to which the fixture is attached. See installation steps for more details (Fig 3.) a. There is one LED module in the fixture. If it does not work, replace it as shown in Fig. 3. Make sure the power is off before you replace. b. Remove crystals (E and E1) from the fixture. c. Loosen screws (H) and plastic washer (N). Remove glass sheet (I), then loosen all thread (J) and plastic washer (N). d. Press quick terminal (K) with small screwdriver (Not included) to disconnect the wires. e. Reverse steps d-b to install new module (L).
Fig.1
Set#A-020-176 -Mounting Plate -Ground Screw -Mounting Screw
Fig 3
Your installation is now complete. Return power to the junction box and test the fixture. Note: Illustration (Fig.1) on this manual is for installation purposes only. It may or may not be identical to the fixture purchased. Dimmable with ELV and/or LED compatible wall dimmer switches. IMPORTANT: Fixtures should be installed by a qualified electrician to ensure proper wiring and installation.
LA-3220E
