ARN 2010 Truffaut Single Sconce
Product Information
The Truffaut Single Sconce, Item # ARN 2010, is a light fixture
designed for installation on walls. It comes with a mounting plate
(B), fixture body (F), screws (E), anchors (A), wood screws (C),
support cable, shade (H), round disc (G), and a light bulb (not
included). The fixture should be installed in accordance with
applicable local installation codes by a person familiar with its
construction and operation.
Product Usage Instructions
- Before starting the installation, carefully inspect the item
and its contents. If any damage or defect is found, do not proceed
with the installation and retain all packaging material. - Prepare the necessary tools: Phillips screwdriver, slotted
screwdriver, drill, and pencil (not included). - Remove all parts from the box and place them on a clean, soft
surface. - Detach the mounting plate (B) from the fixture body (F) by
removing screws (E). - Align the mounting plate (B) with the junction box and mark the
anchor positions using a pencil. - Drill holes in the marked positions using a drill bit slightly
smaller than the anchors (A). - Install the anchors (A) into the holes using a hammer.
- Attach the mounting plate (B) to the junction box using
mounting screws (D), then secure wood screws (C) to the anchors
(A). - Thread the support cable through the hole on the back of the
mounting plate (B). - Ensure all wire connections are tight and neatly tuck them into
the junction box. - Attach the fixture body (F) to the mounting plate (B) using
screws (E). - Install the light bulb into the socket.
- Place the shade (H) onto the round disc (G).
Note: Please refer to Diagram 1 and Diagram 2
for visual guidance during the assembly process.
Care Instructions
To clean the Truffaut Single Sconce, use only a soft dry cloth
or feather duster. Avoid using abrasive or chemical agents as they
may damage the fixture.
ASSEMBLY INSTRUCTIONS
H Bulb not included
G
E
C
A
Diagram 2
F D BI
b a c
Diagram 1
Truffaut Single Sconce
Item # ARN 2010
NOTICE:
This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.
TOOLS REQUIRED (NOT INCLUDED):
Phillips Screwdriver Hammer
Slotted Screwdriver
Drill
Pencil
1. Carefully remove all parts from the box. Place on a clean, soft surface. 2. Remove mounting plate (B) from fixture body (F) by removing
screws (E). 3. Using the mounting plate (B) as a guide, line up with the junction box
and mark anchor positions. 4. Using a drill bit slightly smaller than the anchor, drill holes in the
marked positions. Install anchors (A) into the holes using hammer. 5. Install mounting plate (B) to junction box and secure with mounting
screws (D), then secure wood screws (C) to anchors (A). 6. Run support cable through hole on back of mounting plate (B).
Wrap the support cable around the saddle (a), and secure with u-bolt (b) and hex nuts (c). See diagram 1. 7. Wrap fixture ground wire (green) around the green grounding screw (see diagram 2). Tighten. Continue fixture ground wire and connect to supply ground wire (usually green or bare copper) using wire nut (I). NOTE: It is imperative that the fixture is grounded. 8. Connect fixture neutral wire (white) to the supply neutral wire (usually white) using wire nut (I). 9. Connect fixture hot wire (black) to the supply hot wire (usually black) using wire nut (I). CAUTION: Do not reverse the hot and neutral connections.
ASSEMBLY INSTRUCTIONS
H Bulb not included
E
C
A
Diagram 2
Truffaut Single Sconce Item # ARN 2010
NOTICE: This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.
10. Make sure all wire connections are tight, then carefully tuck into the junction box.
11. Install fixture body (F)to mounting plate (B) and secure with screws (E).
12. Install light bulb into the socket. 13. Place shade (H) onto round disc (G).
Care Instructions: Clean only with a soft dry cloth or feather duster. Do not use abrasive or chemical agents.
G
F D BI
b a c
Diagram 1
