KW 2522 Pertica 14 Inch Sconce

Product Information:

The Pertica 14 Sconce (Item # KW 2522) is a light fixture that
should be installed in accordance with all applicable, local
installation codes. It should be installed by a person familiar
with its construction and operation, as well as the hazards
involved. The fixture comes with a mounting plate, screws, driver,
and quick connectors.

Product Usage Instructions:

1. Carefully remove all parts from the box and place them on a
   clean, soft surface.
2. Remove the mounting plate (C) from the fixture (H) by
   unscrewing the screws (G) using the provided screwdriver (F).
3. Use the mounting plate (C) as a guide to line it up with the
   junction box and mark the anchor positions.
4. Using a drill bit slightly smaller than the anchor size, drill
   holes in the marked positions. Install anchors (B) into the holes
   using a hammer.
5. Connect the driver (J) input neutral wire (white) to the supply
   neutral wire (usually white) using the wire nut (A).
6. Connect the driver (J) input hot wire (black) to the supply hot
   wire (usually black) using the wire nut (A).
   CAUTION: Do not reverse the hot and neutral
   connections.
7. Insert the driver (J) into the junction box.
8. Wrap the supply ground wire (usually green or bare copper)
   around the green grounding screw (refer to Diagram 1) and tighten
   it. NOTE: It is imperative that the fixture is
   grounded.
9. Install the mounting plate (C) to the junction box and secure
   it with the mounting screws (E), then secure the wood screws (D) to
   the anchors (B).
10. Connect the quick connectors (K1) & (K2) together.
11. Install the fixture (H) to the mounting plate (C) and secure it
    with the screws (G) using the provided screwdriver (F).
12. Remove the protective cap (M) from the fixture (H), then thread
    the LED bulb (L) to the fixture (H).
13. Thread the shade (I) to the fixture (H). NOTE:
    Do not over-tighten, otherwise, the glass shade could be
    damaged.

Care Instructions:

Clean the fixture only with a soft dry cloth or feather duster.
Do not use abrasive or chemical agents.

ASSEMBLY INSTRUCTIONS

Diagram 1

A

I

L

M

H

G F

E

+

O-J 60 B2- 2P
cU S
J

D C B K1 K2

Pertica 14″ Sconce
Item # KW 2522
NOTICE: This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.

TOOLS REQUIRED (NOT INCLUDED):

Phillips Screwdriver

Slotted Screwdriver

Drill

Pencil

Hammer

1. Carefully remove all parts from the box. Place on a clean, soft surface. 2. Remove mounting plate (C) from fixture (H) by removing screws (G)
using provided screwdriver (F). 3. Using mounting plate (C) as a guide, line up with the junction box and
mark anchor positions. 4. Using a drill bit slightly smaller than the anchor, drill holes in the
marked positions. Install anchors (B) into the holes using hammer. 5. Connect driver (J) input neutral wire (white) to the supply neutral wire
(usually white) using wire nut (A). 6. Connect driver (J) input hot wire (black) to the supply hot wire (usually
black) using wire nut (A). CAUTION: Do not reverse the hot and neutral connections. 7. Insert driver (J) into junction box. 8. Wrap supply ground wire (usually green or bare copper) around the green grounding screw (see diagram 1). Tighten. NOTE: It is imperative that the fixture is grounded. 9. Install mounting plate (C) to the junction box and secure with mounting screws (E), then secure wood screws (D) to anchors (B). 10. Connect quick connectors (K1) & (K2) together.

M

LI ST ED

US

ASSEMBLY INSTRUCTIONS

Diagram 1

A

I

L

M

H

G F

E

+

O-J 60 B2- 2P
cU S
J

D C B K1 K2

Pertica 14″ Sconce
Item # KW 2522
NOTICE: This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.
11. Install fixture (H) to mounting plate (C) and secure with screws (G) using the provided screwdriver (F).
12. Remove protective cap (M) from fixture (H), then thread LED bulb (L) to fixture (H).
13. Thread shade (I) to fixture (H). NOTE: Do not over-tighten otherwise glass shade could be damaged.
Care Instructions: Clean only with a soft dry cloth or feather duster. Do not use abrasive or chemical agents.

M

LI ST ED

US